International Journal of Industrial and Manufacturing Systems Engineering

Volume 1, Issue 3, November 2016

  • Computer Aided Design and Simulation of Bottled Water Handle

    Hillary Ejike Chukwu, Harold Chukwuemeka Godwin, Uchenna Samuel Ugwu

    Issue: Volume 1, Issue 3, November 2016
    Pages: 45-51
    Received: 13 September 2016
    Accepted: 1 October 2016
    Published: 26 October 2016
    DOI: 10.11648/j.ijimse.20160103.11
    Downloads:
    Views:
    Abstract: In this work, tools such as SolidWorks CAD, SolidWorks Simulation was used in the course of the design of a bottled water handle. This approach provided a less tedious process to its manual counterpart. Every progression of design was assessed and interpreted in detail in this paper. The primary goal of increasing the torsional rigidity and stiffne... Show More
  • Optimization of a New Tool Switching Problem in Flexible Manufacturing Systems with a Tool Life by a Genetic Algorithm

    Hamid Dadashi, Shiva Moslemi, Abolfazl Mirzazadeh

    Issue: Volume 1, Issue 3, November 2016
    Pages: 52-58
    Received: 31 October 2016
    Accepted: 11 November 2016
    Published: 23 December 2016
    DOI: 10.11648/j.ijimse.20160103.12
    Downloads:
    Views:
    Abstract: This paper considers a tool switching problem (ToSP) in flexible manufacturing systems (FMSs). Indeed, a new version of the ToSP that may be faced in practice is proposed. In this paper, a tool life is considered for each tool and a new formulation of the ToSP is presented, however, because of the complexity of such an NP-hard problem, the exact me... Show More
  • The Lumbar Musculoskeletal Disorders in the Factory of Auto Parts Production and Assembly

    Ghorbanali Mohammadi, Fatemeh Nabizadeh Mamani, Elnaz Nabizadeh Mamani

    Issue: Volume 1, Issue 3, November 2016
    Pages: 59-63
    Received: 30 October 2016
    Accepted: 19 November 2016
    Published: 29 December 2016
    DOI: 10.11648/j.ijimse.20160103.13
    Downloads:
    Views:
    Abstract: Introduction: The outbreak of musculoskeletal disorders is a widespread phenomenon among human, and it usually occurs in the back, lumbar, neck, and upper limbs of human. In this study, we have tried to investigate the factors affecting the lumbar disorders in a factory of auto parts production and assembly. In terms of aim, the present study is fu... Show More
  • Optimum WEDM Process Parameters of Incoloy®Alloy800 Using Taguchi Method

    Makkapati Sahiti, Madur Raghavendra Reddy, Budi Joshi, J. Peter Praveen, Boggarapu Nageswara Rao

    Issue: Volume 1, Issue 3, November 2016
    Pages: 64-68
    Received: 15 October 2016
    Accepted: 7 December 2016
    Published: 4 January 2017
    DOI: 10.11648/j.ijimse.20160103.14
    Downloads:
    Views:
    Abstract: Studies are made on the wire electrical discharge machining (WEDM) process performance parameters such as material removal rate, kerf and surface roughness of Incoloy®Alloy800 following the Taguchi’s design of experiments. ANOVA is performed to trace the statistically significance of input parameter (viz. gap voltage, pulse-on-time, pulse-off-time ... Show More
  • Optimum WEDM Process Parameters of SS304 Using Taguchi Method

    P. Bharathi, Tummalapenta Gouri Lalitha Priyanka, G. Srinivasa Rao, Boggarapu Nageswara Rao

    Issue: Volume 1, Issue 3, November 2016
    Pages: 69-72
    Received: 15 October 2016
    Accepted: 12 December 2016
    Published: 10 January 2017
    DOI: 10.11648/j.ijimse.20160103.15
    Downloads:
    Views:
    Abstract: Studies are made on the WEDM process performance parameters such as material removal rate, kerf and surface roughness of SS304 following the Taguchi’s design of experiments. ANOVA is performed to trace the statistically significance of input parameter (viz. voltage, pulse-on-time, pulse-off-time and wire feed) on the output response parameters. A m... Show More