Characterization of Al2O3/Al/Al2O3 Joints with Ti+Cr Interlayer

Marzanna; Maria Ksiazek; Maria; Wieslawa Richert; Lukasz; Rafal Boron; Adam Tchorz

doi:doi:10.11648/j.ijmsa.20140305.14

| Peer-Reviewed

Characterization of Al2O3/Al/Al2O3 Joints with Ti+Cr Interlayer

Marzanna, Maria Ksiazek, Maria, Wieslawa Richert, Lukasz, Rafal Boron, Adam Tchorz

Published in International Journal of Materials Science and Applications (Volume 3, Issue 5)

Received: 20 August 2014 Accepted: 28 August 2014 Published: 10 September 2014

Views: Downloads:

Download PDF

Share This Article

Twitter
Linked In
Facebook

Abstract

Joints of Al2O3/Al/Al2O3 are formed by liquid – state bonding of alumina substrates covered with thin Ti+Cr film of 380 nm thickness using an Al interlayer of 30 µm at 973 K under a vacuum of 0.2 mPa applied for 5 minutes and at a pressure of 0.01 MPa. The bond strength of the joints is examined by a four – point bend testing at room temperature, coupled with optical, scanning and transmission electron microscopy. Results show that introduction of the thin Ti+Cr film layer: (i) improves plasticity in the metal layer of Al2O3/Al/Al2O3 joints, (ii) has positive effect on structure transformation in the interface and leads to fabrication of reliable metal-ceramic joints. Information obtained from the wetting characteristics of liquid Al on alumina substrate coated by thin Ti+Cr film indicates that the contact angle can be reduced to even less than 60°. Microstructural investigations of the interface of Al2O3/Ti+Cr/Al/Ti+Cr/Al2O3 joints carried out by SEM and TEM techniques indicated that the precipitates of intermetallic phases rich in both Ti and Cr as well as Al2O3 were formed at the Al/Al2O3 interface, which influenced strengthening of these joints. Hence a conclusion can be drawn that the interface structure influences the mechanical durability increase in Al/Al2O3 joints.

Published in	International Journal of Materials Science and Applications (Volume 3, Issue 5)
DOI	10.11648/j.ijmsa.20140305.14
Page(s)	152-158
Creative Commons	This is an Open Access article, distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution and reproduction in any medium or format, provided the original work is properly cited.
Copyright	Copyright © The Author(s), 2024. Published by Science Publishing Group

Keywords

Metal–Ceramic Joining, Liquid State Bonding, Bond Strength, Fracture Interface

References

[1]	D.A. Javernick, P.R. Chidambaram, G.R. Edwards, Metall. Mater. Trans., 29A (1998 327-337.
[2]	J.G. Li, Ceramics Interna., 20(1994)391-412.
[3]	E. Saiz, R.M. Cannon, A.P. Tomsia, Acta Mater., 47(1999)4209-4220.
[4]	N. Sobczak, R. Asthana, M. Ksiazek, W. Radziwill, B. Mikulowski, Metall. Mater. Trans., 35A(2004) 911-921.
[5]	G. Ceccone, M.G. Nicholas, S.D. Peteves , A.P. Tomsia, B.J. Dalgleish, A.M. Glaeser, Acta Mater, 44(1996)657-667.
[6]	J.X. Zhang, R.S. Chande, H.P. Seow, Mater. Chem. Phys., 75(2002)256-259.
[7]	M. Ksiazek, N. Sobczak, B. Mikułowski, W. Radziwill, I. Surowiak, Mater. Sci. Eng., A324(2002)162-167.
[8]	A. Strecker, U. Salzberger, J. Mayer, Prakt. Metalogr., 30 (1993)482-495.
[9]	Y. Gao, J. Zhu, Q.G. Cai, Scr. Metal. Mater., 31(1994)571-575.
[10]	T.J. Jewett, M. Dahms, Z. Metallkd., 87(1997)254-261.
[11]	E. Saiz, A.P. Tomsia, K. Suganuma, J. Europ. Ceram. Soc., 23(2003)2787-2796.

Cite This Article

Plain Text BibTeX RIS

APA Style

Marzanna, Maria Ksiazek, Maria, Wieslawa Richert, Lukasz, et al. (2014). Characterization of Al2O3/Al/Al2O3 Joints with Ti+Cr Interlayer. International Journal of Materials Science and Applications, 3(5), 152-158. https://doi.org/10.11648/j.ijmsa.20140305.14

Copy | Download

ACS Style

Marzanna; Maria Ksiazek; Maria; Wieslawa Richert; Lukasz, et al. Characterization of Al2O3/Al/Al2O3 Joints with Ti+Cr Interlayer. Int. J. Mater. Sci. Appl. 2014, 3(5), 152-158. doi: 10.11648/j.ijmsa.20140305.14

Copy | Download

AMA Style

Marzanna, Maria Ksiazek, Maria, Wieslawa Richert, Lukasz, et al. Characterization of Al2O3/Al/Al2O3 Joints with Ti+Cr Interlayer. Int J Mater Sci Appl. 2014;3(5):152-158. doi: 10.11648/j.ijmsa.20140305.14

Copy | Download

@article{10.11648/j.ijmsa.20140305.14,
  author = {Marzanna and Maria Ksiazek and Maria and Wieslawa Richert and Lukasz and Rafal Boron and Adam Tchorz},
  title = {Characterization of Al2O3/Al/Al2O3 Joints with Ti+Cr Interlayer},
  journal = {International Journal of Materials Science and Applications},
  volume = {3},
  number = {5},
  pages = {152-158},
  doi = {10.11648/j.ijmsa.20140305.14},
  url = {https://doi.org/10.11648/j.ijmsa.20140305.14},
  eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.ijmsa.20140305.14},
  abstract = {Joints of Al2O3/Al/Al2O3 are formed by liquid – state bonding of alumina substrates covered with thin Ti+Cr film of 380 nm thickness using an Al interlayer of 30 µm at 973 K under a vacuum of 0.2 mPa applied for 5 minutes and at a pressure of 0.01 MPa. The bond strength of the joints is examined by a four – point bend testing at room temperature, coupled with optical, scanning and transmission electron microscopy. Results show that introduction of the thin Ti+Cr film layer: (i) improves plasticity in the metal layer of Al2O3/Al/Al2O3 joints, (ii) has positive effect on structure transformation in the interface and leads to fabrication of reliable metal-ceramic joints. Information obtained from the wetting characteristics of liquid Al on alumina substrate coated by thin Ti+Cr film indicates that the contact angle can be reduced to even less than 60°. Microstructural investigations of the interface of Al2O3/Ti+Cr/Al/Ti+Cr/Al2O3 joints carried out by SEM and TEM techniques indicated that the precipitates of intermetallic phases rich in both Ti and Cr as well as Al2O3 were formed at the Al/Al2O3 interface, which influenced strengthening of these joints. Hence a conclusion can be drawn that the interface structure influences the mechanical durability increase in Al/Al2O3 joints.},
 year = {2014}
}

Copy | Download

TY  - JOUR
T1  - Characterization of Al2O3/Al/Al2O3 Joints with Ti+Cr Interlayer
AU  - Marzanna
AU  - Maria Ksiazek
AU  - Maria
AU  - Wieslawa Richert
AU  - Lukasz
AU  - Rafal Boron
AU  - Adam Tchorz
Y1  - 2014/09/10
PY  - 2014
N1  - https://doi.org/10.11648/j.ijmsa.20140305.14
DO  - 10.11648/j.ijmsa.20140305.14
T2  - International Journal of Materials Science and Applications
JF  - International Journal of Materials Science and Applications
JO  - International Journal of Materials Science and Applications
SP  - 152
EP  - 158
PB  - Science Publishing Group
SN  - 2327-2643
UR  - https://doi.org/10.11648/j.ijmsa.20140305.14
AB  - Joints of Al2O3/Al/Al2O3 are formed by liquid – state bonding of alumina substrates covered with thin Ti+Cr film of 380 nm thickness using an Al interlayer of 30 µm at 973 K under a vacuum of 0.2 mPa applied for 5 minutes and at a pressure of 0.01 MPa. The bond strength of the joints is examined by a four – point bend testing at room temperature, coupled with optical, scanning and transmission electron microscopy. Results show that introduction of the thin Ti+Cr film layer: (i) improves plasticity in the metal layer of Al2O3/Al/Al2O3 joints, (ii) has positive effect on structure transformation in the interface and leads to fabrication of reliable metal-ceramic joints. Information obtained from the wetting characteristics of liquid Al on alumina substrate coated by thin Ti+Cr film indicates that the contact angle can be reduced to even less than 60°. Microstructural investigations of the interface of Al2O3/Ti+Cr/Al/Ti+Cr/Al2O3 joints carried out by SEM and TEM techniques indicated that the precipitates of intermetallic phases rich in both Ti and Cr as well as Al2O3 were formed at the Al/Al2O3 interface, which influenced strengthening of these joints. Hence a conclusion can be drawn that the interface structure influences the mechanical durability increase in Al/Al2O3 joints.
VL  - 3
IS  - 5
ER  -

Copy | Download

Author Information

Marzanna
Maria Ksiazek
Maria
Wieslawa Richert
Lukasz
Rafal Boron
Adam Tchorz

Foundry Research Institute, Complex of research Laboratories, Cracow, Poland

Download PDF

Sections

Plain Text BibTeX RIS

APA Style

Marzanna, Maria Ksiazek, Maria, Wieslawa Richert, Lukasz, et al. (2014). Characterization of Al2O3/Al/Al2O3 Joints with Ti+Cr Interlayer. International Journal of Materials Science and Applications, 3(5), 152-158. https://doi.org/10.11648/j.ijmsa.20140305.14

Copy | Download

ACS Style

Marzanna; Maria Ksiazek; Maria; Wieslawa Richert; Lukasz, et al. Characterization of Al2O3/Al/Al2O3 Joints with Ti+Cr Interlayer. Int. J. Mater. Sci. Appl. 2014, 3(5), 152-158. doi: 10.11648/j.ijmsa.20140305.14

Copy | Download

AMA Style

Marzanna, Maria Ksiazek, Maria, Wieslawa Richert, Lukasz, et al. Characterization of Al2O3/Al/Al2O3 Joints with Ti+Cr Interlayer. Int J Mater Sci Appl. 2014;3(5):152-158. doi: 10.11648/j.ijmsa.20140305.14

Copy | Download

@article{10.11648/j.ijmsa.20140305.14,
  author = {Marzanna and Maria Ksiazek and Maria and Wieslawa Richert and Lukasz and Rafal Boron and Adam Tchorz},
  title = {Characterization of Al2O3/Al/Al2O3 Joints with Ti+Cr Interlayer},
  journal = {International Journal of Materials Science and Applications},
  volume = {3},
  number = {5},
  pages = {152-158},
  doi = {10.11648/j.ijmsa.20140305.14},
  url = {https://doi.org/10.11648/j.ijmsa.20140305.14},
  eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.ijmsa.20140305.14},
  abstract = {Joints of Al2O3/Al/Al2O3 are formed by liquid – state bonding of alumina substrates covered with thin Ti+Cr film of 380 nm thickness using an Al interlayer of 30 µm at 973 K under a vacuum of 0.2 mPa applied for 5 minutes and at a pressure of 0.01 MPa. The bond strength of the joints is examined by a four – point bend testing at room temperature, coupled with optical, scanning and transmission electron microscopy. Results show that introduction of the thin Ti+Cr film layer: (i) improves plasticity in the metal layer of Al2O3/Al/Al2O3 joints, (ii) has positive effect on structure transformation in the interface and leads to fabrication of reliable metal-ceramic joints. Information obtained from the wetting characteristics of liquid Al on alumina substrate coated by thin Ti+Cr film indicates that the contact angle can be reduced to even less than 60°. Microstructural investigations of the interface of Al2O3/Ti+Cr/Al/Ti+Cr/Al2O3 joints carried out by SEM and TEM techniques indicated that the precipitates of intermetallic phases rich in both Ti and Cr as well as Al2O3 were formed at the Al/Al2O3 interface, which influenced strengthening of these joints. Hence a conclusion can be drawn that the interface structure influences the mechanical durability increase in Al/Al2O3 joints.},
 year = {2014}
}

Copy | Download

TY  - JOUR
T1  - Characterization of Al2O3/Al/Al2O3 Joints with Ti+Cr Interlayer
AU  - Marzanna
AU  - Maria Ksiazek
AU  - Maria
AU  - Wieslawa Richert
AU  - Lukasz
AU  - Rafal Boron
AU  - Adam Tchorz
Y1  - 2014/09/10
PY  - 2014
N1  - https://doi.org/10.11648/j.ijmsa.20140305.14
DO  - 10.11648/j.ijmsa.20140305.14
T2  - International Journal of Materials Science and Applications
JF  - International Journal of Materials Science and Applications
JO  - International Journal of Materials Science and Applications
SP  - 152
EP  - 158
PB  - Science Publishing Group
SN  - 2327-2643
UR  - https://doi.org/10.11648/j.ijmsa.20140305.14
AB  - Joints of Al2O3/Al/Al2O3 are formed by liquid – state bonding of alumina substrates covered with thin Ti+Cr film of 380 nm thickness using an Al interlayer of 30 µm at 973 K under a vacuum of 0.2 mPa applied for 5 minutes and at a pressure of 0.01 MPa. The bond strength of the joints is examined by a four – point bend testing at room temperature, coupled with optical, scanning and transmission electron microscopy. Results show that introduction of the thin Ti+Cr film layer: (i) improves plasticity in the metal layer of Al2O3/Al/Al2O3 joints, (ii) has positive effect on structure transformation in the interface and leads to fabrication of reliable metal-ceramic joints. Information obtained from the wetting characteristics of liquid Al on alumina substrate coated by thin Ti+Cr film indicates that the contact angle can be reduced to even less than 60°. Microstructural investigations of the interface of Al2O3/Ti+Cr/Al/Ti+Cr/Al2O3 joints carried out by SEM and TEM techniques indicated that the precipitates of intermetallic phases rich in both Ti and Cr as well as Al2O3 were formed at the Al/Al2O3 interface, which influenced strengthening of these joints. Hence a conclusion can be drawn that the interface structure influences the mechanical durability increase in Al/Al2O3 joints.
VL  - 3
IS  - 5
ER  -

Copy | Download