International Journal of Energy and Power Engineering

| Peer-Reviewed |

Design and Fabrication of a Dc Driver Circuit Control Dc Motor

Received: 03 January 2013    Accepted:     Published: 20 February 2013
Views:       Downloads:

Share This Article

Abstract

A DC Motor Driver is a device that drives motor, typically as a speed controller of motor. This DC Motor Driver circuit uses a 741 operational amplifier operating as a voltage follower where its non inverting input is connected to the speed and rotation direction of a potentiometer. When the potentiometer is turned towards the positive supply side, the output will go positive voltage and NPN transistor will supply the current to the motor and PNP transistor will be OFF. When the potentiometer is turned to the negative supply side, the op-amp output switches to the negative voltage and NPN Transistor will turn OFF and PNP Transistor ON which reverses the rotation of the motor's direction. It has been design along with Op-Amp to drive the motor. The fabrication results of DC Motor Driver provide very good results. The total cost of fabricated our dc motor driver using Op-Amp is comparatively cheaper than the traditional dc Motor Driver available in market price. A DC Motor specification is taken and corresponding parameters are found out from derived design approach. Ultimately simulation is done for model with and without filter used after reference speed and a comparative study has been done on response of both cases. Further it is purposed that in industrial environment these controllers are better than others controllers as Op-Amp controllers are easy and cheap.

DOI 10.11648/j.ijepe.20130201.11
Published in International Journal of Energy and Power Engineering (Volume 2, Issue 1, February 2013)
Page(s) 1-11
Creative Commons

This is an Open Access article, distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution and reproduction in any medium or format, provided the original work is properly cited.

Copyright

Copyright © The Author(s), 2024. Published by Science Publishing Group

Keywords

Dc Driver Circuit, TB+, Half Cycle

References
[1] B.L Theraja & A.K Theraja, AC & DC Machines, Khanna Publishers, New Delhi, 2003.
[2] Bimbhra, P.S., Power Electronics, Khanna Publishers, New Delhi, 2006.
[3] Dubey, G.K., Fundamentals of Electrical Drives. New Delhi, Narosa Publishing House, 2000.
[4] Rashid, M.H., Power Electronics, Prentice Hall of India, New Delhi, 1993.
[5] Infineon Technologies, Basic DC motor speed PID control with the Infineon Technologies, 1996.
[6] Salam Dr. Zainal, UTJMB, Power Electronics and Drives (Version 3-2003).
[7] Gopal, M., Control Systems, Principles and Design. New Delhi, Tata McGraw Hill Publishing Company limited 2008.
[8] J.D Nicould, O Matthey and G.Caprari, "Control and Analysis of Low Inertia Miniature Synchronous Motors". International Symposium on Micromehantronics and Human Science, 1998.
[9] Advanced PM brushless DC motor control and system for electric vehicle, Fang Lin Luo; Hock Guan Yeo, 1990.
[10] Delmar, Herman, Stephen L. Cengage Learning, Electric Motor Control, 9th ed. 2009.
[11] http://www.electronics-project-design.com.
Author Information
  • Dept of EEE World University of Bangladesh

  • Dept of EEE World University of Bangladesh

Cite This Article
  • APA Style

    Diponkar Paul, Rajib Mondal. (2013). Design and Fabrication of a Dc Driver Circuit Control Dc Motor. International Journal of Energy and Power Engineering, 2(1), 1-11. https://doi.org/10.11648/j.ijepe.20130201.11

    Copy | Download

    ACS Style

    Diponkar Paul; Rajib Mondal. Design and Fabrication of a Dc Driver Circuit Control Dc Motor. Int. J. Energy Power Eng. 2013, 2(1), 1-11. doi: 10.11648/j.ijepe.20130201.11

    Copy | Download

    AMA Style

    Diponkar Paul, Rajib Mondal. Design and Fabrication of a Dc Driver Circuit Control Dc Motor. Int J Energy Power Eng. 2013;2(1):1-11. doi: 10.11648/j.ijepe.20130201.11

    Copy | Download

  • @article{10.11648/j.ijepe.20130201.11,
      author = {Diponkar Paul and Rajib Mondal},
      title = {Design and Fabrication of a Dc Driver Circuit Control Dc Motor},
      journal = {International Journal of Energy and Power Engineering},
      volume = {2},
      number = {1},
      pages = {1-11},
      doi = {10.11648/j.ijepe.20130201.11},
      url = {https://doi.org/10.11648/j.ijepe.20130201.11},
      eprint = {https://download.sciencepg.com/pdf/10.11648.j.ijepe.20130201.11},
      abstract = {A DC Motor Driver is a device that drives motor, typically as a speed controller of motor. This DC Motor Driver circuit uses a 741 operational amplifier operating as a voltage follower where its non inverting input is connected to the speed and rotation direction of a potentiometer. When the potentiometer is turned towards the positive supply side, the output will go positive voltage and NPN transistor will supply the current to the motor and PNP transistor will be OFF. When the potentiometer is turned to the negative supply side, the op-amp output switches to the negative voltage and NPN Transistor will turn OFF and PNP Transistor ON which reverses the rotation of the motor's direction. It has been design along with Op-Amp to drive the motor. The fabrication results of DC Motor Driver provide very good results. The total cost of fabricated our dc motor driver using Op-Amp is comparatively cheaper than the traditional dc Motor Driver available in market price. A DC Motor specification is taken and corresponding parameters are found out from derived design approach. Ultimately simulation is done for model with and without filter used after reference speed and a comparative study has been done on response of both cases. Further it is purposed that in industrial environment these controllers are better than others controllers as Op-Amp controllers are easy and cheap.},
     year = {2013}
    }
    

    Copy | Download

  • TY  - JOUR
    T1  - Design and Fabrication of a Dc Driver Circuit Control Dc Motor
    AU  - Diponkar Paul
    AU  - Rajib Mondal
    Y1  - 2013/02/20
    PY  - 2013
    N1  - https://doi.org/10.11648/j.ijepe.20130201.11
    DO  - 10.11648/j.ijepe.20130201.11
    T2  - International Journal of Energy and Power Engineering
    JF  - International Journal of Energy and Power Engineering
    JO  - International Journal of Energy and Power Engineering
    SP  - 1
    EP  - 11
    PB  - Science Publishing Group
    SN  - 2326-960X
    UR  - https://doi.org/10.11648/j.ijepe.20130201.11
    AB  - A DC Motor Driver is a device that drives motor, typically as a speed controller of motor. This DC Motor Driver circuit uses a 741 operational amplifier operating as a voltage follower where its non inverting input is connected to the speed and rotation direction of a potentiometer. When the potentiometer is turned towards the positive supply side, the output will go positive voltage and NPN transistor will supply the current to the motor and PNP transistor will be OFF. When the potentiometer is turned to the negative supply side, the op-amp output switches to the negative voltage and NPN Transistor will turn OFF and PNP Transistor ON which reverses the rotation of the motor's direction. It has been design along with Op-Amp to drive the motor. The fabrication results of DC Motor Driver provide very good results. The total cost of fabricated our dc motor driver using Op-Amp is comparatively cheaper than the traditional dc Motor Driver available in market price. A DC Motor specification is taken and corresponding parameters are found out from derived design approach. Ultimately simulation is done for model with and without filter used after reference speed and a comparative study has been done on response of both cases. Further it is purposed that in industrial environment these controllers are better than others controllers as Op-Amp controllers are easy and cheap.
    VL  - 2
    IS  - 1
    ER  - 

    Copy | Download

  • Sections