Experimental and CFD Investigation the Effect of Solid Particle Height in Water-Solid Flow in Fluidized Bed Column

Riyadh S. Al-Turaihi; Sarah H. Oleiwi

doi:doi:10.11648/j.ijmea.20150303.12

| Peer-Reviewed

Experimental and CFD Investigation the Effect of Solid Particle Height in Water-Solid Flow in Fluidized Bed Column

Riyadh S. Al-Turaihi, Sarah H. Oleiwi

Published in International Journal of Mechanical Engineering and Applications (Volume 3, Issue 3)

Received: 22 May 2015 Accepted: 3 June 2015 Published: 17 June 2015

Views: Downloads:

Download PDF

Share This Article

Twitter
Linked In
Facebook

Abstract

The liquid solid fluidized beds have been usually used in catalytic cracking, ion exchange, crystallization, and particle classification. Fluidized bed column has investigated experimentally and numerically. A numerical investigation has been done by using computational fluid dynamic software ANSYS Fluent 15.0. In this study, a spherical stainless steel has used as solid particle fluidized continuously by water. Three different values of water flow rate (10, 15, 20 l/min) have used with three different values of static head of the solid particles (2, 2.5, 3 cm). The pressure of the fluidized bed has been measured at four different location of the test section 20 cm apart and the flow behavior at the test section has monitored by using AOS high speed camera. The experimental data has compared with numerical solution and a good agreement has been found. It can be observed that the expansion of the solid particles and the pressure inside the bed increased as the water flow rate and static bed height increased.

Published in	International Journal of Mechanical Engineering and Applications (Volume 3, Issue 3)
DOI	10.11648/j.ijmea.20150303.12
Page(s)	37-45
Creative Commons	This is an Open Access article, distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution and reproduction in any medium or format, provided the original work is properly cited.
Copyright	Copyright © The Author(s), 2024. Published by Science Publishing Group

Keywords

Fluidized Bed, Two Phase Flow, CFD, Ansys Fluent

References

[1]	Reza Davarnejad, Reza Eshghipour, Jafar Abdi and Farhad Banisharif Dehkordi, “CFD Modeling of a Binary Liquid-Solid Fluidized Bed”, Middle-East Journal of Scientific Research, 19 (10): 1272-1279, 2014.
[2]	Tingwen Li, Aytekin Gel, Sreekanth Pannala, Mehrdad Shahnam, Madhava Syamlal, “CFD simulations of circulating fluidized bed risers, part I: Grid study”, Powder Technology, 254 - 170–180, 2014.
[3]	Kenichi Hashizume, Shinichi Morita, Yuki Nakamura, and Akira Wada,” Pressure Drop in Liquid–Solid Circulating Fluidized Beds”, Heat Transfer—Asian Research, 38 (4), 2009.
[4]	Dinesh V. Kalaga, Rupesh K. Reddy, Jyeshtharaj B. Joshi, Sameer V. Dalvi, K. Nandkumar, “Liquid phase axial mixing in solid–liquid circulating multistage fluidized bed: CFD modeling and RTD measurements”, Chemical Engineering Journal, 191- 475– 490, 2012.
[5]	Riyadh S. Al-Turaihi, Ahmed Kadhim Hussein, Hussain H. Al-Kayiem and H. A. Mohammed, “Experimental Investigation of Various Solid Particle Materials on the Steady State Gas-Solid Fluidized Bed System”, J. Basic. Appl. Sci. Res., 3(7)293-304, 2013.
[6]	Youjun Lu, Liang Zhao, Qiang Han, Liping Wei, Ximin Zhang, Liejin Guo, Jinjia Wei, “Minimum fluidization velocities for supercritical water fluidized bed within the range of 633–693 K and 23–27 MPa”, International Journal of Multiphase Flow, 49 - 78–82, 2013.
[7]	Chanchal Loha, Himadri Chattopadhyay, Pradip K. Chatterjee, “Euler-Euler CFD modeling of fluidized bed: Influence of specularity coefficient on hydrodynamic behavior”, Particuology, 11- 673– 680, 2013.
[8]	Bo LECKNER, Genadij I. PALCHONOK, and Filip JOHNSSON, “PRESSURE FLUCTUATIONS IN GAS FLUIDIZED BEDS”, Original scientific paper, 0354–9836, 6 , 2, 3-11, 2002.
[9]	K.V. Ramesh, G.M.J. Raju, G.V.S. Sarma, C. Bhaskara Sarma, “Effect of internal on phase holdups of a three-phase fluidized bed”, Chemical Engineering Journal, 145-393–398, 2009.
[10]	Farshid Vejahati, Nader Mahinpey, Naoko Ellis and Mehrdokht B. Nikoo, “CFD Simulation of Gas–Solid Bubbling Fluidized Bed: A New Method for Adjusting Drag Law”, Can. J. Chem. Eng., 87:19–30, 2009.
[11]	Ansys 13.0 Help, Fluent Theory Guide, Mixture Multiphase Model.
[12]	Ansys Fluent Tutorials, Fluidized bed.

Cite This Article

Plain Text BibTeX RIS

APA Style

Riyadh S. Al-Turaihi, Sarah H. Oleiwi. (2015). Experimental and CFD Investigation the Effect of Solid Particle Height in Water-Solid Flow in Fluidized Bed Column. International Journal of Mechanical Engineering and Applications, 3(3), 37-45. https://doi.org/10.11648/j.ijmea.20150303.12

Copy | Download

ACS Style

Riyadh S. Al-Turaihi; Sarah H. Oleiwi. Experimental and CFD Investigation the Effect of Solid Particle Height in Water-Solid Flow in Fluidized Bed Column. Int. J. Mech. Eng. Appl. 2015, 3(3), 37-45. doi: 10.11648/j.ijmea.20150303.12

Copy | Download

AMA Style

Riyadh S. Al-Turaihi, Sarah H. Oleiwi. Experimental and CFD Investigation the Effect of Solid Particle Height in Water-Solid Flow in Fluidized Bed Column. Int J Mech Eng Appl. 2015;3(3):37-45. doi: 10.11648/j.ijmea.20150303.12

Copy | Download

@article{10.11648/j.ijmea.20150303.12,
  author = {Riyadh S. Al-Turaihi and Sarah H. Oleiwi},
  title = {Experimental and CFD Investigation the Effect of Solid Particle Height in Water-Solid Flow in Fluidized Bed Column},
  journal = {International Journal of Mechanical Engineering and Applications},
  volume = {3},
  number = {3},
  pages = {37-45},
  doi = {10.11648/j.ijmea.20150303.12},
  url = {https://doi.org/10.11648/j.ijmea.20150303.12},
  eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.ijmea.20150303.12},
  abstract = {The liquid solid fluidized beds have been usually used in catalytic cracking, ion exchange, crystallization, and particle classification. Fluidized bed column has investigated experimentally and numerically. A numerical investigation has been done by using computational fluid dynamic software ANSYS Fluent 15.0. In this study, a spherical stainless steel has used as solid particle fluidized continuously by water. Three different values of water flow rate (10, 15, 20 l/min) have used with three different values of static head of the solid particles (2, 2.5, 3 cm). The pressure of the fluidized bed has been measured at four different location of the test section 20 cm apart and the flow behavior at the test section has monitored by using AOS high speed camera. The experimental data has compared with numerical solution and a good agreement has been found. It can be observed that the expansion of the solid particles and the pressure inside the bed increased as the water flow rate and static bed height increased.},
 year = {2015}
}

Copy | Download

TY  - JOUR
T1  - Experimental and CFD Investigation the Effect of Solid Particle Height in Water-Solid Flow in Fluidized Bed Column
AU  - Riyadh S. Al-Turaihi
AU  - Sarah H. Oleiwi
Y1  - 2015/06/17
PY  - 2015
N1  - https://doi.org/10.11648/j.ijmea.20150303.12
DO  - 10.11648/j.ijmea.20150303.12
T2  - International Journal of Mechanical Engineering and Applications
JF  - International Journal of Mechanical Engineering and Applications
JO  - International Journal of Mechanical Engineering and Applications
SP  - 37
EP  - 45
PB  - Science Publishing Group
SN  - 2330-0248
UR  - https://doi.org/10.11648/j.ijmea.20150303.12
AB  - The liquid solid fluidized beds have been usually used in catalytic cracking, ion exchange, crystallization, and particle classification. Fluidized bed column has investigated experimentally and numerically. A numerical investigation has been done by using computational fluid dynamic software ANSYS Fluent 15.0. In this study, a spherical stainless steel has used as solid particle fluidized continuously by water. Three different values of water flow rate (10, 15, 20 l/min) have used with three different values of static head of the solid particles (2, 2.5, 3 cm). The pressure of the fluidized bed has been measured at four different location of the test section 20 cm apart and the flow behavior at the test section has monitored by using AOS high speed camera. The experimental data has compared with numerical solution and a good agreement has been found. It can be observed that the expansion of the solid particles and the pressure inside the bed increased as the water flow rate and static bed height increased.
VL  - 3
IS  - 3
ER  -

Copy | Download

Author Information

Riyadh S. Al-Turaihi

Mechanical Department, College of Engineering, Babylon University, Babylon, Iraq
Sarah H. Oleiwi

Mechanical Department, College of Engineering, Babylon University, Babylon, Iraq

Download PDF

Sections

Plain Text BibTeX RIS

APA Style

Riyadh S. Al-Turaihi, Sarah H. Oleiwi. (2015). Experimental and CFD Investigation the Effect of Solid Particle Height in Water-Solid Flow in Fluidized Bed Column. International Journal of Mechanical Engineering and Applications, 3(3), 37-45. https://doi.org/10.11648/j.ijmea.20150303.12

Copy | Download

ACS Style

Riyadh S. Al-Turaihi; Sarah H. Oleiwi. Experimental and CFD Investigation the Effect of Solid Particle Height in Water-Solid Flow in Fluidized Bed Column. Int. J. Mech. Eng. Appl. 2015, 3(3), 37-45. doi: 10.11648/j.ijmea.20150303.12

Copy | Download

AMA Style

Riyadh S. Al-Turaihi, Sarah H. Oleiwi. Experimental and CFD Investigation the Effect of Solid Particle Height in Water-Solid Flow in Fluidized Bed Column. Int J Mech Eng Appl. 2015;3(3):37-45. doi: 10.11648/j.ijmea.20150303.12

Copy | Download

@article{10.11648/j.ijmea.20150303.12,
  author = {Riyadh S. Al-Turaihi and Sarah H. Oleiwi},
  title = {Experimental and CFD Investigation the Effect of Solid Particle Height in Water-Solid Flow in Fluidized Bed Column},
  journal = {International Journal of Mechanical Engineering and Applications},
  volume = {3},
  number = {3},
  pages = {37-45},
  doi = {10.11648/j.ijmea.20150303.12},
  url = {https://doi.org/10.11648/j.ijmea.20150303.12},
  eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.ijmea.20150303.12},
  abstract = {The liquid solid fluidized beds have been usually used in catalytic cracking, ion exchange, crystallization, and particle classification. Fluidized bed column has investigated experimentally and numerically. A numerical investigation has been done by using computational fluid dynamic software ANSYS Fluent 15.0. In this study, a spherical stainless steel has used as solid particle fluidized continuously by water. Three different values of water flow rate (10, 15, 20 l/min) have used with three different values of static head of the solid particles (2, 2.5, 3 cm). The pressure of the fluidized bed has been measured at four different location of the test section 20 cm apart and the flow behavior at the test section has monitored by using AOS high speed camera. The experimental data has compared with numerical solution and a good agreement has been found. It can be observed that the expansion of the solid particles and the pressure inside the bed increased as the water flow rate and static bed height increased.},
 year = {2015}
}

Copy | Download

TY  - JOUR
T1  - Experimental and CFD Investigation the Effect of Solid Particle Height in Water-Solid Flow in Fluidized Bed Column
AU  - Riyadh S. Al-Turaihi
AU  - Sarah H. Oleiwi
Y1  - 2015/06/17
PY  - 2015
N1  - https://doi.org/10.11648/j.ijmea.20150303.12
DO  - 10.11648/j.ijmea.20150303.12
T2  - International Journal of Mechanical Engineering and Applications
JF  - International Journal of Mechanical Engineering and Applications
JO  - International Journal of Mechanical Engineering and Applications
SP  - 37
EP  - 45
PB  - Science Publishing Group
SN  - 2330-0248
UR  - https://doi.org/10.11648/j.ijmea.20150303.12
AB  - The liquid solid fluidized beds have been usually used in catalytic cracking, ion exchange, crystallization, and particle classification. Fluidized bed column has investigated experimentally and numerically. A numerical investigation has been done by using computational fluid dynamic software ANSYS Fluent 15.0. In this study, a spherical stainless steel has used as solid particle fluidized continuously by water. Three different values of water flow rate (10, 15, 20 l/min) have used with three different values of static head of the solid particles (2, 2.5, 3 cm). The pressure of the fluidized bed has been measured at four different location of the test section 20 cm apart and the flow behavior at the test section has monitored by using AOS high speed camera. The experimental data has compared with numerical solution and a good agreement has been found. It can be observed that the expansion of the solid particles and the pressure inside the bed increased as the water flow rate and static bed height increased.
VL  - 3
IS  - 3
ER  -

Copy | Download