Volume 7, Issue 4, December 2019, Pages: 114-117
Received: Aug. 8, 2019;
Accepted: Oct. 31, 2019;
Published: Dec. 4, 2019
Views 555 Downloads 134
Md. Nazrul Islam, Department of Physics, Primeasia University, Banani, Dhaka, Bangladesh
M. A. Gafur, Pilot Plant and Process Development Center, BCSIR, Dhaka, Bangladesh
Today we are more concern about the environment. Synthetic polymers are the most responsible pollutant for environmental pollution. Good replacing agents for the synthetic polymers are the natural polymer. That is why the uses of natural fiber reinforced composites are increasing day-by-day. In this research natural polymer coir fiber was used as the reinforcing agent with the synthetic polymer polypropylene. PP-coir composites were fabricated using a simple hot press molding method. The prepared composites were characterized by the density, tensile, and flexural properties. The effect of fiber addition on some physical and mechanical properties was evaluated. The density increases with the increase of fiber addition. The tensile strength of fabricated product increases with the increase of fiber addition up to 10% (wt.) and then decreases continuously. The elongation of fabricated product decreases with the increase of fiber addition continuously. The changes in the mechanical properties were broadly related to the accompanying interfacial bonding of PP- coir composites (PPCC). It revealed that the introduction of short coir fiber led to a slightly improved thermo oxidative stability of PP- Coir composites. The flexural strain of fabricated product decreases continuously with the increase of fiber addition. But here untreated fiber reinforced composites show higher strain than that of treated fiber reinforced composites.
Md. Nazrul Islam,
M. A. Gafur,
PP-coir Composites (PPCC): Fabrication and Study of Flexural Properties, Modern Chemistry.
Vol. 7, No. 4,
2019, pp. 114-117.
Copyright © 2019 Authors retain the copyright of this article.
This article is an open access article distributed under the Creative Commons Attribution License (http://creativecommons.org/licenses/by/4.0/
) which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.
Sahadat Hossain M, Uddin MB, Razzak M, Sarwaruddin Chowdhury AM, Khan RA. Fabrication and characterization of jute fabrics reinforced polypropylene-based composites: effects of ionizing radiation and disaccharide (sucrose). Radiation Effects and Defects in Solids. 2017 Dec 2; 172 (11-12): 904-14.
Sahadat Hossain, Md, AM Sarwaruddin Chowdhury, and Ruhul A. Khan. "Effect of disaccharide, gamma radiation and temperature on the physico-mechanical properties of jute fabrics reinforced unsaturated polyester resin-based composite." Radiation Effects and Defects in Solids 172, no. 5-6 (2017): 517-530.
Shahriar Kabir M, Hossain MS, Mia M, Islam M, Rahman M, Hoque MB, Chowdhury AM. Mechanical Properties of Gamma-Irradiated Natural Fiber Reinforced Composites. InNano Hybrids and Composites 2018 (Vol. 23, pp. 24-38). Trans Tech Publications.
Hoque MB, Hossain MS, Nahid AM, Bari S, Khan RA. Fabrication and Characterization of Pineapple Fiber-Reinforced Polypropylene Based Composites. InNano Hybrids and Composites 2018 (Vol. 21, pp. 31-42). Trans Tech Publications.
Rahaman MN, Hossain MS, Razzak M, Uddin MB, Chowdhury AS, Khan RA. Effect of dye and temperature on the physico-mechanical properties of jute/PP and jute/LLDPE based composites. Heliyon. 2019 Jun 1; 5 (6): e01753.
A. Gafur And M. A. Rashid, Natural Fiber Reinforced Polymer (Coir-Hdpe) Matrix Composites- Fabrication, Process Parameters And Properties, 2nd Bsme-Asme International Conference On Thermal Engineering, 2-4 Januray, 2004, Dhaka, Bangladesh, Voll-Ii, P. 1078-1082.
M. A. Gafur, M N Hassan And Akram Hossain, Natural Fiber-Polymer (Jute-Ldpe) Matrix Composites – Its Fabrication, Process Parameter, And Properties, 3rd International Conference On Mechanical Engineering And 8th Apm On E-Manufacturing, Ieb Bangladesh, Me Div, 20-22 March, 2003, Paper No. 22, Dhaka, Bangladesh, P. 163-167.
Bipasha Bose, Effect Of Water Absorption On The Mechanical Properties Of Jute Fiber Reinforced Polymer Composites, June, 2005.
Herzog, R. O. And Jancke, W., Physik, Z., 1920, 3, 106.
Shabname Ele, Development And Characterization Of Pp-Bagass Composites, December, 2003.
Md. Akbar Hossain Miah, Reyad Mehfuz, Syed Misbah Uddin, Mechanical Properties Of Short Jute Fiber Reinforced Hdpe Composite.
Sarce Report; Natural Fiber Conceret-Report From A Sarec – Financed Research And Development Project Hans – Enik Gram Hao kan Persson Ao ke Sharendahl, P17.
Md. Mydul Alam, Development Of A New Composite With Natural Fiber (Udal) And Synthetic Polymer (Ethylene Vinyl Acetate) And The Studies of Its Mechanical Properties, July, 2005.
William D. Callister, Jr., Material Science and Engineering And Introduction. P130-131.
Hull D An Introduction To Composite Materials, Cambridge University Press, 1981.