American Journal of Modern Physics

| Peer-Reviewed |

Effect of MgO Addition on the Mechanical and Thermal Properties of Mullite Synthesised through Reaction Sintering of Al2O3 and Algerian Kaolin

Received: 19 June 2013    Accepted:     Published: 20 September 2013
Views:       Downloads:

Share This Article

Abstract

The influence of MgO addition on the structure and properties of mullite prepared through reaction sintering of Algerian kaolin and Al2O3 was investigated. The raw powders were wet ball milled, dried and cold compacted using a uniaxial press. The green compacts were sintered 8 hours at 1600 and 1650°C. The microstructure of samples was characterized using a scanning electron microscope. Mechanical and thermal properties were characterized using Vicker’s hardness tester, a universal testing machine and a dilatometer. It was found that the increase of MgO content from 0 to 3 wt-% increased the hardness of samples sintered 8 hours at 1600°C from 1039 to 1316.57 HV. Also, the increase of MgO content in samples sintered 8 hours at 1600 and 1650°C increased the compressive strength up to a maximum then decreased it. For a sintering temperature of 1600°C, the increase of MgO content up to 2 wt-% increased the flexural strength, but a further increase of MgO to 3 wt-% decreased it again, while for a sintering temperature of 1650°C, the increase of MgO content from 0 to 3 wt-% increased the flexural strength from 103.45 to 472.25 MPa. Amongst MgO containing samples, the increase of MgO content increased the coefficient of thermal expansion; however, it remained lower than the coefficient of thermal expansion of the sample without MgO addition.

DOI 10.11648/j.ajmp.20130205.16
Published in American Journal of Modern Physics (Volume 2, Issue 5, September 2013)
Page(s) 270-275
Creative Commons

This is an Open Access article, distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution and reproduction in any medium or format, provided the original work is properly cited.

Copyright

Copyright © The Author(s), 2024. Published by Science Publishing Group

Keywords

Kaolin, Mullite, Alumina, Reaction Sintering, Mechanical Properties, Thermal Properties

References
[1] M. Rahmani, K. Jangorban and S. Otroj, Ceramics-Silikaty, 56, 215-221 (2012)
[2] J. Roy, N. Bandyopadhyay, S. Das and , S. Maitra, Ceramics-Silikaty, 54, 128-132 (2010)
[3] H. Belhouchet, M. Hamidouche, N. Bouaouadja, V. Garnier and G. Fantozzi, Ceramics-Silikaty, 53, 205-210 (2009).
[4] V. Viswabaskaran, F.D. Gnanam and M. Balasubramanian, Ceram. Inter., 28, 557-564 (2002)
[5] V. Viswabaskaran, F.D. Gnanam and M. Balasubramanian, Ceram. Inter., 29, 561-571 (2003)
[6] V. Viswabaskaran, F.D. Gnanam and M. Balasubramanian, Appl. Clay Sci., 25, 2935 (2004).
[7] E. Kamseu, S. Braccini, A. Corradi and C. Leonelli, Adv. App. Ceram., 108, 338-346 (2009)
[8] T. Ebadzadeh, M.H. Sarrafi and E. Salahi, Ceram. Inter., 35, 3175-3179 (2009)
[9] B. Bagchi, S. Das and A. Bhattacharya, R. Basu and P. Nandy, App. Clay Sci., 47, 409-413 (2010)
[10] A. Esharghawi, C. Penot and F. Nardou, J. Eur. Ceram. Soc., 29, 31-38 (2009)
[11] A. Esharghawi, C. Penot and F. Nardou, Ceram. Inter., 36, 231-239 (2010).
[12] F. Sahnoune, M. Chegaar, N. Saheb, P. Goeuriot and F. Valdivieso, App. Clay Sci., 38, 304-310 (2008).
[13] W.E. Lee and W.M. Rainforth, Ceramic Microstructures: Property Control by Processing, Chapman & Hall, London 1994.
[14] M.G.M.U. Ismail, H. Tsunatori and Z. Nakai, J. Mater. Sci., 25, 2619-2625 (1990).
[15] C. Galassi, E. Roncari, C. Bassarello and R. Lapasin, J. Am. Ceram. Soc., 82, 3453-3458 (1999).
[16] L. Montanaro, C. Perrot, C. Esnouf, G. Thollet, G. Fantozzi and A. Negro, J. Am. Ceram. Soc., 83, 189-196 (2000).
[17] D. Doni Jayaseelan, D. Amutha Rani, D.Benny Anburaj and T. Ohji, Ceram. Inter., 30, 539-543 (2004).
[18] V. Viswabaskaran, F.D.Gnanam and M. Balasubramanian, App. Clay Sci., 25, 29-35 (2004).
[19] W.M.N. Nour and H.M. Awad, J. Aust. Ceram. Soc., 44, 27-37 (2008).
[20] W.M.N. Nour and H.M. Awad, Ce Ca, 38, 111-120 (2008).
[21] D. Amutha Rani, D. Doni Jayaseelan and F.D. Gnanam, J. Eur. Ceram. Soc., 21, 2253-2257 (2001).
[22] S.H. Hong, W. Cermignani and G.L. Messing, J. Eur. Ceram. Soc., 16, 133-141 (1996).
[23] S.H. Hong and G.L. Messing, J. Am. Ceram. Soc., 81, 1269-1277 (1998).
[24] P. Mechnich, M. Schmucker and H.Schneider, J. Am. Ceram. Soc., 82, 2517-2522 (1999).
[25] J. Roy, N. Bandyopadhyay, S. Das and S. Maitra, Ceram. Inter., 36, 1603-1608 (2010).
[26] P.M. Souto, R.R. Menezes and R.H.G.A. Kiminami, J. Mater. Proc. Tech., 209, 548-553 (2009).
[27] F. Sahnoune, M. Chegaar, N. Saheb, P. Goeuriot and F. Valdivieso, Adv. App. Ceram., 107, 9-13 (2008).
[28] F. Sahnoune, N. Saheb B. Khamel and Z. Takkouk, J. Therm. Anal. Calorim., 107, 1067-1072 (2012).
[29] M. Heraiz, A. Merrouche and N. Saheb, Adv. App. Ceram , 105, 285-290 (2006).
[30] Y. Hirata, K. Sakeda, Y. Matsushita, K. Shimada and Y.J. Ishihara, Am. Ceram. Soc., 72, 995-1002 (1989).
[31] R. Torrecillas, J.M. Calderon, J.S. Moya, M.J. Reece, C.K.L. Davies, C. Olagnon and G. Fantozzi, J. Eur. Ceram. Soc., 19, 2519-2527 (1999).
[32] C.D. Beachem: Microscopic fracture processes, Academic Press, Liebowitz 1968.
[33] S. Somiya and Y. Hirata, Am. Ceram. Soc. Bull., 70, 1624-1632 (1991).
Author Information
  • Laboratory of Physics and Chemistry of Materials, University of M’sila, 28000, M’sila, Algeria

  • Laboratory of Physics and Chemistry of Materials, University of M’sila, 28000, M’sila, Algeria

  • Laboratory of Physics and Chemistry of Materials, University of M’sila, 28000, M’sila, Algeria

  • Laboratory of Non Metallic Materials, IOMP, University of Setif 1, 19000, Algeria

  • Research Unit on Emerging Materials (RUEM), University of Setif 1, 19000, Algeria; Laboratory of Physics and Mechanics of Metallic Materials (LP3M), University of Setif 1, 19000, Algeria

  • Department of Mechanical Engineering, King Fahd University of Petroleum and Minerals, Dahran, 31261, Saudi Arabia

Cite This Article
  • APA Style

    A. Ouali, M. Heraiz, F. Sahnoune, H. Belhouchet, M. Fatmi, et al. (2013). Effect of MgO Addition on the Mechanical and Thermal Properties of Mullite Synthesised through Reaction Sintering of Al2O3 and Algerian Kaolin. American Journal of Modern Physics, 2(5), 270-275. https://doi.org/10.11648/j.ajmp.20130205.16

    Copy | Download

    ACS Style

    A. Ouali; M. Heraiz; F. Sahnoune; H. Belhouchet; M. Fatmi, et al. Effect of MgO Addition on the Mechanical and Thermal Properties of Mullite Synthesised through Reaction Sintering of Al2O3 and Algerian Kaolin. Am. J. Mod. Phys. 2013, 2(5), 270-275. doi: 10.11648/j.ajmp.20130205.16

    Copy | Download

    AMA Style

    A. Ouali, M. Heraiz, F. Sahnoune, H. Belhouchet, M. Fatmi, et al. Effect of MgO Addition on the Mechanical and Thermal Properties of Mullite Synthesised through Reaction Sintering of Al2O3 and Algerian Kaolin. Am J Mod Phys. 2013;2(5):270-275. doi: 10.11648/j.ajmp.20130205.16

    Copy | Download

  • @article{10.11648/j.ajmp.20130205.16,
      author = {A. Ouali and M. Heraiz and F. Sahnoune and H. Belhouchet and M. Fatmi and N. Saheb},
      title = {Effect of MgO Addition on the Mechanical and Thermal Properties of Mullite Synthesised through Reaction Sintering of Al2O3 and Algerian Kaolin},
      journal = {American Journal of Modern Physics},
      volume = {2},
      number = {5},
      pages = {270-275},
      doi = {10.11648/j.ajmp.20130205.16},
      url = {https://doi.org/10.11648/j.ajmp.20130205.16},
      eprint = {https://download.sciencepg.com/pdf/10.11648.j.ajmp.20130205.16},
      abstract = {The influence of MgO addition on the structure and properties of mullite prepared through reaction sintering of Algerian kaolin and Al2O3 was investigated. The raw powders were wet ball milled, dried and cold compacted using a uniaxial press. The green compacts were sintered 8 hours at 1600 and 1650°C. The microstructure of samples was characterized using a scanning electron microscope. Mechanical and thermal properties were characterized using Vicker’s hardness tester, a universal testing machine and a dilatometer. It was found that the increase of MgO content from 0 to 3 wt-% increased the hardness of samples sintered 8 hours at 1600°C from 1039 to 1316.57 HV. Also, the increase of MgO content in samples sintered 8 hours at 1600 and 1650°C increased the compressive strength up to a maximum then decreased it. For a sintering temperature of 1600°C, the increase of MgO content up to 2 wt-% increased the flexural strength, but a further increase of MgO to 3 wt-% decreased it again, while for a sintering temperature of 1650°C, the increase of MgO content from 0 to 3 wt-% increased the flexural strength from 103.45 to 472.25 MPa. Amongst MgO containing samples, the increase of MgO content increased the coefficient of thermal expansion; however, it remained lower than the coefficient of thermal expansion of the sample without MgO addition.},
     year = {2013}
    }
    

    Copy | Download

  • TY  - JOUR
    T1  - Effect of MgO Addition on the Mechanical and Thermal Properties of Mullite Synthesised through Reaction Sintering of Al2O3 and Algerian Kaolin
    AU  - A. Ouali
    AU  - M. Heraiz
    AU  - F. Sahnoune
    AU  - H. Belhouchet
    AU  - M. Fatmi
    AU  - N. Saheb
    Y1  - 2013/09/20
    PY  - 2013
    N1  - https://doi.org/10.11648/j.ajmp.20130205.16
    DO  - 10.11648/j.ajmp.20130205.16
    T2  - American Journal of Modern Physics
    JF  - American Journal of Modern Physics
    JO  - American Journal of Modern Physics
    SP  - 270
    EP  - 275
    PB  - Science Publishing Group
    SN  - 2326-8891
    UR  - https://doi.org/10.11648/j.ajmp.20130205.16
    AB  - The influence of MgO addition on the structure and properties of mullite prepared through reaction sintering of Algerian kaolin and Al2O3 was investigated. The raw powders were wet ball milled, dried and cold compacted using a uniaxial press. The green compacts were sintered 8 hours at 1600 and 1650°C. The microstructure of samples was characterized using a scanning electron microscope. Mechanical and thermal properties were characterized using Vicker’s hardness tester, a universal testing machine and a dilatometer. It was found that the increase of MgO content from 0 to 3 wt-% increased the hardness of samples sintered 8 hours at 1600°C from 1039 to 1316.57 HV. Also, the increase of MgO content in samples sintered 8 hours at 1600 and 1650°C increased the compressive strength up to a maximum then decreased it. For a sintering temperature of 1600°C, the increase of MgO content up to 2 wt-% increased the flexural strength, but a further increase of MgO to 3 wt-% decreased it again, while for a sintering temperature of 1650°C, the increase of MgO content from 0 to 3 wt-% increased the flexural strength from 103.45 to 472.25 MPa. Amongst MgO containing samples, the increase of MgO content increased the coefficient of thermal expansion; however, it remained lower than the coefficient of thermal expansion of the sample without MgO addition.
    VL  - 2
    IS  - 5
    ER  - 

    Copy | Download

  • Sections