A Review Paper on: Effect of Different Types of Filler Materials on Marshall Characteristics of Bitumen Hot Mix
International Journal of Materials Science and Applications
Volume 9, Issue 3, May 2020, Pages: 40-46
Received: Aug. 11, 2020; Accepted: Sep. 14, 2020; Published: Sep. 24, 2020
Views 40      Downloads 33
Authors
Gazi Mohammad Harun-Or-Rashid, Department of Civil Engineering, Rajshahi University of Engineering & Technology, Rajshahi, Bangladesh
Mohammad Mohayminul Islam, Department of Civil Engineering, Rajshahi University of Engineering & Technology, Rajshahi, Bangladesh
Article Tools
Follow on us
Abstract
Bituminous hot mix is one of the most widely used and costly flexible pavement layer. It involves a huge outlay of investment. Precise engineering and usage of proper materials can make it more cost efficient, durable, convenient for users and most importantly ecofriendly. To reduce the cost of construction engineers all over the globe are investigating for the alternative material to obtain same amount of output (strength, stability and durability) by paying a little. There are four constituents of a hot mix, coarse aggregate, fine aggregate, binder and filler. Filler in the bitumen hot mix fill the void in between the aggregates which is very important for strength and stability of the pavement. But the fillers are conventionally used (cement and lime) are very costly which affect the total cost of construction. That’s why the researchers emphasized on the waste material to serve this purpose as well as to keep the environment clean. A large range of waste material like fly ash, bagasse ash, marble dust, stone dust, brick dust, kiln dust, waste concrete dust, foundry sand, bio gypsum, ceramic dust etc. has been use as a filler for numerous research works by the researchers globally. The materials yielded very satisfactory results. Fly ash, bagasse results in nearly same Marshall properties (stability, OBC, %VFA, %VMA, %Va) like the conventional one. Although the brick dust and stone dust provide a high amount of air voids but they also result high stability. More or less all these non-conventional materials are capable to fully or partially replace the conventional filler. This study focused on the effect on the Marshall hot mix design properties after using these fillers mentioned above.
Keywords
Marshall Mix Design, Filler, Bitumen Hot Mix, Marshall Properties, Hot Mix Asphalt, HMA
To cite this article
Gazi Mohammad Harun-Or-Rashid, Mohammad Mohayminul Islam, A Review Paper on: Effect of Different Types of Filler Materials on Marshall Characteristics of Bitumen Hot Mix, International Journal of Materials Science and Applications. Vol. 9, No. 3, 2020, pp. 40-46. doi: 10.11648/j.ijmsa.20200903.11
Copyright
Copyright © 2020 Authors retain the copyright of this article.
This article is an open access article distributed under the Creative Commons Attribution License (http://creativecommons.org/licenses/by/4.0/) which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.
References
[1]
Kareem. A. I. “Evaluation of Recycled Cement Concrete (RCC) as Filler for Asphalt Mixture”. Journal of Engineering and Development, Vol. 18, No. 5, September 2014, ISSN 1813-7822.
[2]
Rahman. A., Ali. S. A., Adhikary. S. K. and Hossain. Q. S. “Effect Of Fillers On Bituminous Paving Mixes: An Experimental Study”. Journal of Engineering Science 03 (1), 2012 121-127.
[3]
Sutradhar. D., Miah. M., Chowdhury. G. J., Sobhan. M. A. “Effect of Using Waste Material as Filler in Bituminous Mix Design”. American Journal of Civil Engineering 2015; 3 (3): 88-94.
[4]
Fatima. E., Sahu. S., Jhamb. A., and Kumar. R., “Use of Ceramic Waste as Filler in Semi-Dense Bituminous Concrete.” American Journal of Civil Engineering and Architecture, vol. 2, no. 3 (2014): 102-106. doi: 10.12691/ajcea-2-3-2.
[5]
Kar. D., Panda. M. and Giri. J. P. “Influence Of Fly-Ash As A Filler In Bituminous Mixes”. ARPN Journal of Engineering and Applied Sciences. VOL. 9, NO. 6, JUNE 2014.
[6]
Muaran. A. A. and Sani. L. “Partial Replacement Of Partial Replacement Of Cement With Bagasse Ash In Hot Mix Cement With Bagasse Ash In Hot Mix Asphaltasphalt”. Nigerian Journal of Technology (NIJOTECH) Vol. 34 No. 4, October 2015, pp. 699–704.
[7]
Joni. H. H. and Zghair. H. H. “Effect of Adding Used-Foundry Sand on Hot Asphalt Mixtures Performance”. Eng. & Tech. Journal, Vol. 34, Part (A), No. 6, 2016.
[8]
Sert. T. K. and Kütük. S. “Physical and Marshall Properties of Borogyps um Used as Filler Aggregate in Asphalt Concre te”. Journal of Materials in Civil En-gineering, Vol. 25, No. 2, February 1, 2013. © ASCE, ISSN 0899-1561/2013/2-266-273/$25.00.
[9]
Anderson, D. A., Bahia, H. U. and Dongre, R. “Rheological properties of mineral filler asphalt mastics and their relationship to pavement performance”, ASTM STP 1147, Richard C. Meininger, Ed., American Society for Testing Materials, Philadelphia, U.S.A., 1992.
[10]
Vavrik, W. R., Pine, W. J., Carpenter, S. H., and Bailey, R. “Bailey method for gradation selection in hot-mix asphalt mixture design”. Transportation Research Board, National Research Council, Washington, D. C., USA, 2002.
[11]
Qiu, Y. “Design and performance of stone mastic asphalt in Singapore conditions”, PhD thesis, Nanyang Technological University, Singapore, 2006.
[12]
Grabowski. W. and Wilanowicz. J. “The structure of mineral fillers and their stiffening properties in filler-bitumen mastics”, Materials and structures, vol. 44, pp. 793–804, 2008.
[13]
Gubler. R., Liu. Y., Anderson. D. A., and Partl. M. N. “Investigation of the system filler and asphalt binders by rheological means”, Journal of the Association of Asphalt Paving Technologists, vol. 68, pp. 284–304, 1999.
[14]
Recasens. R. M., Martinez. A., Jimenez. F. P. and Bianchetto. H. “Effect of filler on the aging potential of asphalt mixtures”, Transportation Research Record: Journal of the Transportation Research Board, 1901, pp. 10–17, 2005.
[15]
Specification for Road and Bridge Works, Ministry of Road Transport & Highways, 5’th Edition, 2013, New Delhi 11064.
[16]
Polish National Specification: Technical Guidelines for Aggregates for Asphalt Mixures WT-1, 2014.
[17]
Wasilewska, M., Małaszkiewicz. D. and Ignatiuk. N. “Evaluation of Different Mineral Filler Aggregates for Asphalt Mixtures”. IOP Conf. Series: Materials Science and Engineering 245 (2017). doi: 10.1088/1757-899X/245/2/022042.
[18]
Pappu. A., Saxena. M. and Asolekar S. R. “Solid wastes generation in India and their recycling potential in building materia”. Building and Environment 42, 2007, 2311 –2320. doi: 10.1016/j.buildenv.2006.04.015.
[19]
IS: 2386 (1963), “Methods of Test for Aggregates for Concrete (P-III): Specific Gravity, Density, Voids, Absorption, Bulking”, Bureau of Indian Standards, New Delhi.
[20]
IS: 2386 (1963), “Methods of Test for Aggregates for Concrete (P-IV): Mechanical Properties”, Bureau of Indian Standards, New Delhi.
[21]
IS: 1203 (1978), “Methods for Testing Tar and Bituminous Materials: Determination of Penetration”, Bureau of Indian Standards, New Delhi.
[22]
Hassan. H. J. and Israa Y. J. (2010), “The Effect of Using Glass Power filler on Hot Asphalt Concrete Mixture Properties”, Engg and Technology journal, vol. 29, Issue1, pp 44-57.
[23]
Xue. Y., Hou. H., Zhu. S. and Zha. J. (2009), “Utilization of Municipal Solid Waste Incineration Ash in Stone Mastic Asphalt Mixture: Pavement Performance and Environmental Impact”, Construction and Building Materials, Vol. 23, Issue 2, pp 989-996.
[24]
Mustafa. K. and Serdal. T. (2007), “Evaluation of marbal waste dust in mixture of asphalt matrix”, Construction and Building Materials, Volume 21, Issue 5, pp 616-620.
[25]
Melotti. R., Santagata. E., Bassani. M., Salvo. M., and Rizzo. S., “A preliminary investigation into the physical and chemical properties of biomass ashes used as aggregate fillers for bituminous mixtures”, Waste Management, vol. 33, pp. 1906-1917, 2013.
[26]
Wu S., Zhu J., Zhong J. and Wang D., (2011), "Experimental Investigation on Related Properties of Asphalt Mastic Containing Recycled Red Brick Powder." Journal of Construction and Building Materials, Vol. 25, PP. 2883–2887.
[27]
Roberts. F. L., Mohammad. L. and Wang. L. History of Hot Mix Asphalt Mixture Design in the United States. Journal of Materials in Civil Engineering. DOI: 10.1061/(ASCE)0899-1561(2002)14:4(279).
[28]
Mogawer. W. S. and Stuart. K. D. Effects of Mineral Fillers on Properties of Stone Matrix Asphalt Mixtures. Journal of the Transportation Research Board. https://doi.org/10.1177/0361198196153000111
ADDRESS
Science Publishing Group
1 Rockefeller Plaza,
10th and 11th Floors,
New York, NY 10020
U.S.A.
Tel: (001)347-983-5186