Effects of Aspect Ratios on Flow Friction and Thermal Behavior Inside a Close Domain Using Lattice Boltzmann Method
American Journal of Applied Mathematics
Volume 3, Issue 1-1, January 2015, Pages: 1-7
Received: Nov. 11, 2014;
Accepted: Nov. 12, 2014;
Published: Nov. 29, 2014
Views 2909 Downloads 118
M. A. Taher, Dept. of Mechanical and Automotive Engineering, Pukyong National University, Busan 608-739, Korea
Litan Kumar Saha, Department of Applied Mathematics, University of Dhaka, Dhaka, Bangladesh
Y. W. Lee, Dept. of Mechanical and Automotive Engineering, Pukyong National University, Busan 608-739, Korea
Numerical study of flow friction and thermal behavior on a moving lid of a triangular cavity with various aspect ratios has been discussed using a Thermal Lattice Boltzmann Method (TLBM). To analyze the combined force and free convection, known as mixed convection, flows and heat transfer process in a lid driven triangular cavity with various aspect ratios AR(=L/H)=0.5, 1.0 and 2.0 are taken into account in the present study. The results are presented as stream function in terms of velocity, average heat transfer rate in terms of Nusselt number (Nu), and friction on moving lid of cavity for different Reynolds number (Re) as well as buoyancy parameter (λ). The heat transfer rate and friction on moving lid increased and decreased significantly with increasing Reynolds number and aspect ratios but they are linearly and very slowly changed with buoyancy effects. Similarly, the fluid flow behavior significantly changed with higher Reynolds number and aspect ratios compare to lower Re and AR. In addition, the less friction and more heat transfer occurred at case of free convection dominant case compare to forced convection dominant case. Similar behavior is observed for fluid flow analysis inside cavity. The model is validated by other numerical scheme and a very good agreement is found.
M. A. Taher,
Litan Kumar Saha,
Y. W. Lee,
Effects of Aspect Ratios on Flow Friction and Thermal Behavior Inside a Close Domain Using Lattice Boltzmann Method, American Journal of Applied Mathematics. Special Issue:Fluid Flow and Heat Transfer Inside a Closed Domain.
Vol. 3, No. 1-1,
2015, pp. 1-7.
C. Sun, B. Yu, H. F. Oztop, Yi. Wnag, and J. Wei, “Control of mixed convection in lid-driven enclosures using conductive triangular fins”, Int. J. Heat and Mass Transfer, Vol. 54, pp. 894-909, 2011.
M. Li, and T. Tang, “Steady viscous flow in a triangular cavity by efficient numerical techniques”, Computers Math. App.,Vol. 31, No.10, pp.55-65, 1996.
M. Ahmed, and H. C. Kuhlmann, “Flow instability in triangular lid-driven cavities with wall motion away from a rectangular corner”, Fluid Dyn. Res., Vol.44, pp.025501-21, 2012.
C-L Chen, and C-H.Cheng, “Numerical study of flow and thermal behavior of lid-driven flows in cavities of small aspect ratios”, Int. J. Num. Methods in Fluid, Vol.52, pp.785-799, 2006.
T. Basak, G. Aravind, and S. Roy, “Visualization of heat flow due to natural convection within triangular cavities using Bejan’s heatline concept”, Int. J. of Heat and Mass Transfer, Vol.52, pp.2824-2833, 2009.
Y. H. Qian, D. D’Humieres, and , P. Lallemand, “Lattice BGK models for Navier- Stokes equation”, Euro physics letter, Vol. 17, No.6, pp. 479-484, 1992.
H. Chen, S. Chen, and W. H. Matthaeus, “Recovery of the Navier-Stokes equations using a lattice-gas Boltzmann method”, Physical Review A, Vol. 45, No.8, pp. 5339-5342, 1992.
X. He, S. Chen, and G. D. Doolen, “A novel thermal model for the Lattice Boltzmann method in incompressible limit”, J. Comp. Physics, Vol.146, pp. 282-300, 1988.
M. A. Taher, S. C. Saha, Y. W Lee, and H. D. Kim, “Numerical study of lid driven square cavity with heat generation using LBM”, Americal Journal of Fluid Mechanics, Vol.3, No.2, pp.340-344, 2013.
A. Mohammad, Applied lattice Boltzmann method for Transport phenomena, momentum, heat and mass transfer, The University of Calgary, Albetra, Canada, 2007.
Succi, S., The lattice Boltzmann equation for fluid dynamics and beyond, Oxford University, UK, 2001.
A. R. Darzi, M. Farhadi, K. Sedighi, E. Fattahi, and H. Nemati, “Mixed convection simulation on inclined lid driven cavity using Lattice Boltzmann method”, IJST, Transactions of Mechanical Engineering, Vol. 35, No. M1, pp.73–83, 2011.
M. Jafari, M. Farhadi, K. Sedighi, and E. Fattahi, “Numerical simulation of convection heat transfer in a lid driven cavity with an open side”, World Academy of Science, Engineering and Tecnology, Vol.5, No.11, pp.291-295, 2011.
Z. Guo, and T. S. Zhao, “A Lattice Boltzamnn model for convection heat transfer in porous media”, Numerical Heat Transfer, Part B, Vol.47, pp.157-177, 2005.