The Preparation and Experimental Research for Inner Cladding Casting of Al-Al
Science Discovery
Volume 5, Issue 7, December 2017, Pages: 515-518
Received: Dec. 28, 2017; Published: Dec. 28, 2017
Views 844      Downloads 51
Authors
Zeng Li-kui, College of Intelligent Manufacturing and Automobile, Chongqing Technology and Business College, Chongqing, China
Yang Ping, College of Intelligent Manufacturing and Automobile, Chongqing Technology and Business College, Chongqing, China
Wang Yajun, College of Material Science and Engineering, Chongqing University, Chongqing, China
Article Tools
Follow on us
Abstract
With the rapid development of science and technology, the unceasing enhancement of component integration degree, and the increasingly demanding of parts using conditions, the part that the traditional metal materials and alloy materials preparation is hard to meet the requirements of the use of some special conditions, so the new composite materials have been paid attention to by the countries all over the world. An casting method for Inner Cladding Casting was introduced. By the use of this method, the Al-Al inner cladding casting which has the transition layer in the middle was prepared, it was indicated that the casting method for inner cladding casting has the feasibility. Through the soaking experiments of three group samples which were Arc Spraying Al layer、substrate of Al and Inner Cladding Casting of Al-Al, we find out that by 140h soaking experiments for inner cladding casting of Al-Al the porosity change was little and it had shown very good corrosion resistant effect.
Keywords
Al-Al, Arc Spraying, Inner Boundary, Cladding
To cite this article
Zeng Li-kui, Yang Ping, Wang Yajun, The Preparation and Experimental Research for Inner Cladding Casting of Al-Al, Science Discovery. Vol. 5, No. 7, 2017, pp. 515-518. doi: 10.11648/j.sd.20170507.17
References
[1]
刘慧芳,高瑾,李晓刚,吴俊升.高速电弧喷涂FeCrAl涂层和3Cr13涂层的冲刷腐蚀性能[J].中国腐蚀与防护学报,2008,(04):225-230。
[2]
胡小刚.319S铝合金高固相分数半固态压铸多尺度数值模拟方法与实验研究[D].北京:北京科技大学,2016。
[3]
华绍春,王汉功,汪刘应,张武,刘顾.热喷涂技术的研究进展[J].金属热处理,2008,(05):82-87。
[4]
徐荣正,宋刚,刘黎明.铝合金表面电弧喷涂铝涂层工艺与性能[J].焊接学报,2008,(06):109-112。
[5]
房元明,徐骏,高志华,张志峰.7075铝合金流变压铸数值模拟及实验研究[J].稀有金属,2016,(06):283-286。
[6]
A. Okuno, H. Kawano, J. Sun, M. Kurokawa, M. Nalkoka. Feasible Development of Soft—Switdled Sit Invener vith Load-adaptive Frequency-Tracking Control Scheme for Induction Heating [J]. IEEE—Transactions on industry Applications, 1998, 35(6): 713-718.
[7]
Mario Tama, Development of channel of core Type Iduction Furnaces [J], Industrial Heating, 1974(6): 43-45.
[8]
D, V, AlexaIldro, solidification with a Quasiequilibrium Two-phase zone [J], Acta mater, 2001, 49(4): 759-764.
[9]
Hashi M M, Otomo S, DeVdopmet of High Performance Roll by continuous Pouring Process for Cladding [J]. ISIJ, 1992, 11(32): 202-203.
[10]
KISH ITAKE K. Thermal sp rayed Fe210Cr213P27C amorphous coatings possessing excelled corrosion resistance [J]. Journal of Thermal Sp raing Thchnology, 1996, 5(4):476-481.
[11]
刘贵民,徐滨士,库日多夫斯基等.电弧及高速电弧喷涂FeCrAl涂层的微观性能研究[J].中国表面工程,1999,44(3):11-14。
[12]
郭睿,何汉军,曾大新,杜红.液-液复合制备灰铸铁-球墨铸铁双材料铸件的工艺研究[J].铸造,2017,(01):25-27。
ADDRESS
Science Publishing Group
1 Rockefeller Plaza,
10th and 11th Floors,
New York, NY 10020
U.S.A.
Tel: (001)347-983-5186