The Preparation and Experimental Research for Inner Cladding Casting of Al-Al

Zeng Li-kui; Yang Ping; Wang Yajun

doi:doi:10.11648/j.sd.20170507.17

| Peer-Reviewed

The Preparation and Experimental Research for Inner Cladding Casting of Al-Al

Zeng Li-kui, Yang Ping, Wang Yajun

Published in Science Discovery (Volume 5, Issue 7)

Received: 28 December 2017 Accepted: Published: 28 December 2017

Views: Downloads:

Download PDF

Share This Article

Twitter
Linked In
Facebook

Abstract

With the rapid development of science and technology, the unceasing enhancement of component integration degree, and the increasingly demanding of parts using conditions, the part that the traditional metal materials and alloy materials preparation is hard to meet the requirements of the use of some special conditions, so the new composite materials have been paid attention to by the countries all over the world. An casting method for Inner Cladding Casting was introduced. By the use of this method, the Al-Al inner cladding casting which has the transition layer in the middle was prepared, it was indicated that the casting method for inner cladding casting has the feasibility. Through the soaking experiments of three group samples which were Arc Spraying Al layer、substrate of Al and Inner Cladding Casting of Al-Al, we find out that by 140h soaking experiments for inner cladding casting of Al-Al the porosity change was little and it had shown very good corrosion resistant effect.

Published in	Science Discovery (Volume 5, Issue 7)
DOI	10.11648/j.sd.20170507.17
Page(s)	515-518
Creative Commons	This is an Open Access article, distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution and reproduction in any medium or format, provided the original work is properly cited.
Copyright	Copyright © The Author(s), 2024. Published by Science Publishing Group

Keywords

Al-Al, Arc Spraying, Inner Boundary, Cladding

References

[1]	刘慧芳，高瑾，李晓刚，吴俊升.高速电弧喷涂FeCrAl涂层和3Cr13涂层的冲刷腐蚀性能[J].中国腐蚀与防护学报，2008,(04):225-230。
[2]	胡小刚．319S铝合金高固相分数半固态压铸多尺度数值模拟方法与实验研究[D]．北京：北京科技大学，2016。
[3]	华绍春，王汉功，汪刘应，张武，刘顾.热喷涂技术的研究进展[J].金属热处理，2008,(05):82-87。
[4]	徐荣正，宋刚，刘黎明.铝合金表面电弧喷涂铝涂层工艺与性能[J].焊接学报，2008,(06):109-112。
[5]	房元明，徐骏，高志华，张志峰.7075铝合金流变压铸数值模拟及实验研究[J].稀有金属，2016,(06):283-286。
[6]	A. Okuno, H. Kawano, J. Sun, M. Kurokawa, M. Nalkoka. Feasible Development of Soft—Switdled Sit Invener vith Load-adaptive Frequency-Tracking Control Scheme for Induction Heating [J]. IEEE—Transactions on industry Applications, 1998, 35(6): 713-718.
[7]	Mario Tama, Development of channel of core Type Iduction Furnaces [J], Industrial Heating, 1974(6): 43-45.
[8]	D, V, AlexaIldro, solidification with a Quasiequilibrium Two-phase zone [J], Acta mater, 2001, 49(4): 759-764.
[9]	Hashi M M, Otomo S, DeVdopmet of High Performance Roll by continuous Pouring Process for Cladding [J]. ISIJ, 1992, 11(32): 202-203.
[10]	KISH ITAKE K. Thermal sp rayed Fe210Cr213P27C amorphous coatings possessing excelled corrosion resistance [J]. Journal of Thermal Sp raing Thchnology, 1996, 5(4):476-481.
[11]	刘贵民，徐滨士，库日多夫斯基等.电弧及高速电弧喷涂FeCrAl涂层的微观性能研究[J].中国表面工程，1999,44(3):11-14。
[12]	郭睿，何汉军，曾大新，杜红.液-液复合制备灰铸铁-球墨铸铁双材料铸件的工艺研究[J].铸造，2017,(01):25-27。

Cite This Article

Plain Text BibTeX RIS

APA Style

Zeng Li-kui, Yang Ping, Wang Yajun. (2017). The Preparation and Experimental Research for Inner Cladding Casting of Al-Al. Science Discovery, 5(7), 515-518. https://doi.org/10.11648/j.sd.20170507.17

Copy | Download

ACS Style

Zeng Li-kui; Yang Ping; Wang Yajun. The Preparation and Experimental Research for Inner Cladding Casting of Al-Al. Sci. Discov. 2017, 5(7), 515-518. doi: 10.11648/j.sd.20170507.17

Copy | Download

AMA Style

Zeng Li-kui, Yang Ping, Wang Yajun. The Preparation and Experimental Research for Inner Cladding Casting of Al-Al. Sci Discov. 2017;5(7):515-518. doi: 10.11648/j.sd.20170507.17

Copy | Download

@article{10.11648/j.sd.20170507.17,
  author = {Zeng Li-kui and Yang Ping and Wang Yajun},
  title = {The Preparation and Experimental Research for Inner Cladding Casting of Al-Al},
  journal = {Science Discovery},
  volume = {5},
  number = {7},
  pages = {515-518},
  doi = {10.11648/j.sd.20170507.17},
  url = {https://doi.org/10.11648/j.sd.20170507.17},
  eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.sd.20170507.17},
  abstract = {With the rapid development of science and technology, the unceasing enhancement of component integration degree, and the increasingly demanding of parts using conditions, the part that the traditional metal materials and alloy materials preparation is hard to meet the requirements of the use of some special conditions, so the new composite materials have been paid attention to by the countries all over the world. An casting method for Inner Cladding Casting was introduced. By the use of this method, the Al-Al inner cladding casting which has the transition layer in the middle was prepared, it was indicated that the casting method for inner cladding casting has the feasibility. Through the soaking experiments of three group samples which were Arc Spraying Al layer、substrate of Al and Inner Cladding Casting of Al-Al, we find out that by 140h soaking experiments for inner cladding casting of Al-Al the porosity change was little and it had shown very good corrosion resistant effect.},
 year = {2017}
}

Copy | Download

TY  - JOUR
T1  - The Preparation and Experimental Research for Inner Cladding Casting of Al-Al
AU  - Zeng Li-kui
AU  - Yang Ping
AU  - Wang Yajun
Y1  - 2017/12/28
PY  - 2017
N1  - https://doi.org/10.11648/j.sd.20170507.17
DO  - 10.11648/j.sd.20170507.17
T2  - Science Discovery
JF  - Science Discovery
JO  - Science Discovery
SP  - 515
EP  - 518
PB  - Science Publishing Group
SN  - 2331-0650
UR  - https://doi.org/10.11648/j.sd.20170507.17
AB  - With the rapid development of science and technology, the unceasing enhancement of component integration degree, and the increasingly demanding of parts using conditions, the part that the traditional metal materials and alloy materials preparation is hard to meet the requirements of the use of some special conditions, so the new composite materials have been paid attention to by the countries all over the world. An casting method for Inner Cladding Casting was introduced. By the use of this method, the Al-Al inner cladding casting which has the transition layer in the middle was prepared, it was indicated that the casting method for inner cladding casting has the feasibility. Through the soaking experiments of three group samples which were Arc Spraying Al layer、substrate of Al and Inner Cladding Casting of Al-Al, we find out that by 140h soaking experiments for inner cladding casting of Al-Al the porosity change was little and it had shown very good corrosion resistant effect.
VL  - 5
IS  - 7
ER  -

Copy | Download

Author Information

Zeng Li-kui

College of Intelligent Manufacturing and Automobile, Chongqing Technology and Business College, Chongqing, China
Yang Ping

College of Intelligent Manufacturing and Automobile, Chongqing Technology and Business College, Chongqing, China
Wang Yajun

College of Material Science and Engineering, Chongqing University, Chongqing, China

Download PDF

Sections

Plain Text BibTeX RIS

APA Style

Zeng Li-kui, Yang Ping, Wang Yajun. (2017). The Preparation and Experimental Research for Inner Cladding Casting of Al-Al. Science Discovery, 5(7), 515-518. https://doi.org/10.11648/j.sd.20170507.17

Copy | Download

ACS Style

Zeng Li-kui; Yang Ping; Wang Yajun. The Preparation and Experimental Research for Inner Cladding Casting of Al-Al. Sci. Discov. 2017, 5(7), 515-518. doi: 10.11648/j.sd.20170507.17

Copy | Download

AMA Style

Zeng Li-kui, Yang Ping, Wang Yajun. The Preparation and Experimental Research for Inner Cladding Casting of Al-Al. Sci Discov. 2017;5(7):515-518. doi: 10.11648/j.sd.20170507.17

Copy | Download

@article{10.11648/j.sd.20170507.17,
  author = {Zeng Li-kui and Yang Ping and Wang Yajun},
  title = {The Preparation and Experimental Research for Inner Cladding Casting of Al-Al},
  journal = {Science Discovery},
  volume = {5},
  number = {7},
  pages = {515-518},
  doi = {10.11648/j.sd.20170507.17},
  url = {https://doi.org/10.11648/j.sd.20170507.17},
  eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.sd.20170507.17},
  abstract = {With the rapid development of science and technology, the unceasing enhancement of component integration degree, and the increasingly demanding of parts using conditions, the part that the traditional metal materials and alloy materials preparation is hard to meet the requirements of the use of some special conditions, so the new composite materials have been paid attention to by the countries all over the world. An casting method for Inner Cladding Casting was introduced. By the use of this method, the Al-Al inner cladding casting which has the transition layer in the middle was prepared, it was indicated that the casting method for inner cladding casting has the feasibility. Through the soaking experiments of three group samples which were Arc Spraying Al layer、substrate of Al and Inner Cladding Casting of Al-Al, we find out that by 140h soaking experiments for inner cladding casting of Al-Al the porosity change was little and it had shown very good corrosion resistant effect.},
 year = {2017}
}

Copy | Download

TY  - JOUR
T1  - The Preparation and Experimental Research for Inner Cladding Casting of Al-Al
AU  - Zeng Li-kui
AU  - Yang Ping
AU  - Wang Yajun
Y1  - 2017/12/28
PY  - 2017
N1  - https://doi.org/10.11648/j.sd.20170507.17
DO  - 10.11648/j.sd.20170507.17
T2  - Science Discovery
JF  - Science Discovery
JO  - Science Discovery
SP  - 515
EP  - 518
PB  - Science Publishing Group
SN  - 2331-0650
UR  - https://doi.org/10.11648/j.sd.20170507.17
AB  - With the rapid development of science and technology, the unceasing enhancement of component integration degree, and the increasingly demanding of parts using conditions, the part that the traditional metal materials and alloy materials preparation is hard to meet the requirements of the use of some special conditions, so the new composite materials have been paid attention to by the countries all over the world. An casting method for Inner Cladding Casting was introduced. By the use of this method, the Al-Al inner cladding casting which has the transition layer in the middle was prepared, it was indicated that the casting method for inner cladding casting has the feasibility. Through the soaking experiments of three group samples which were Arc Spraying Al layer、substrate of Al and Inner Cladding Casting of Al-Al, we find out that by 140h soaking experiments for inner cladding casting of Al-Al the porosity change was little and it had shown very good corrosion resistant effect.
VL  - 5
IS  - 7
ER  -

Copy | Download