Characterization of Glass Fibre Reinforced Polymer Composite Prepared by Hand Layup Method
American Journal of Bioscience and Bioengineering
Volume 5, Issue 1, February 2017, Pages: 8-11
Received: Dec. 18, 2016;
Accepted: Jan. 10, 2017;
Published: Feb. 4, 2017
Views 5116 Downloads 305
Abdullah Al Mahmood, Department of Glass & Ceramic Engineering, Rajshahi University of Engineering & Technology (RUET), Rajshahi, Bangladesh
Abdul Mobin, Department of Glass & Ceramic Engineering, Rajshahi University of Engineering & Technology (RUET), Rajshahi, Bangladesh
Rezwon Morshed, Department of Glass & Ceramic Engineering, Rajshahi University of Engineering & Technology (RUET), Rajshahi, Bangladesh
Tasmia Zaman, Department of Glass & Ceramic Engineering, Rajshahi University of Engineering & Technology (RUET), Rajshahi, Bangladesh
Follow on us
In this work, glass fiber reinforced epoxy composites were fabricated. Epoxy resin was used as polymer matrix material and glass fiber was used as reinforcing material. The main focus of this work was to fabricate this composite material by the cheapest and easiest way. For this, hand layup method was used to fabricate glass fiber reinforced epoxy resin composites and TiO2 material was used as filler material. Six types of compositions were made with and without filler material keeping the glass fiber constant and changing the epoxy resin with respect to filler material addition. Mechanical properties such as tensile, impact, hardness, compression and flexural properties were investigated. Additionally, microscopic analysis was done. The experimental investigations show that without filler material the composites exhibit overall lower value in mechanical properties than with addition of filler material in the composites. The results also show that addition of filler material increases the mechanical properties but highest values were obtained for different filler material addition. From the obtained results, it was observed that composites filled by 15wt% of TiO2 particulate exhibited maximum tensile strength, 20wt% of TiO2 particulate exhibited maximum impact strength, 25wt% of TiO2 particulate exhibited maximum hardness value, 25wt% of TiO2 particulate exhibited maximum compressive strength, 20wt% of TiO2 particulate exhibited maximum flexural strength.
Glass Fiber, Polymer Composites, Epoxy Resin, Filler
To cite this article
Abdullah Al Mahmood,
Characterization of Glass Fibre Reinforced Polymer Composite Prepared by Hand Layup Method, American Journal of Bioscience and Bioengineering.
Vol. 5, No. 1,
2017, pp. 8-11.
Copyright © 2017 Authors retain the copyright of this article.
This article is an open access article distributed under the Creative Commons Attribution License (http://creativecommons.org/licenses/by/4.0/
) which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.
Tong L., Mouritz A. P., Bannister M. 3D Fibre Reinforced Polymer Composites. Elsevier 2002.
O. P KHANNA “A Text Book of MATERIAL SCIENCE AND METALLURGY”. 1st edition (1993), 23-1.
Patil Deogonda, Vijaykumar N Chalwa. “Mechanical Property of Glass Fiber Reinforcement Epoxy Composites”. Vol. 1, Issue 4 (2013).
R. N. Rothon, “Mineral Fillers in Thermoplastics: Filler Manufacture and Characterization,” Advances in Polymer Science, Vol. 139, 1999, pp. 67-107.
Cs. Varga, N. Miskolczi, L. Bartha and G. Lipoczi, “Im- proving the Mechanical Properties of Glass-Fibre-Rein- forced Polyester Composites by Modification of Fibre Surface,” Materials and Design, Vol. 31, 2010, pp. 185-193.
Khanam P. N., “Journal of polymer and the environment”, “Sisal / carbon fiber reinforced hybrid Composites: tensile, flexural & chemical resistance properties”, Vo. 18, N.4, 2010, 727.
Hanna W. A., Gharib F. E. & Marhoon I. I., “Journal of Minerals & Materials Characterization & Engineering”, “Characterization of ceramic filled polymer matrix composite used for biomedical application”, Vo.10, N.12, 2011, 1167-1178.
MYERS D. S.,” University of Oklahoma Graduate College”, ”Fiber-Reinforced Concrete and Bridge Deck cracking”, 2006, 48.
Saleh E. S., Shabib K. R. & Hamad Q. A., “Eng. & Tech. Journal”, “Studying mechanical properties for polymer matrix composite material reinforced by fibers and particles”, Vo.28, N.4, (2010), PP.86. (In Arabic.
SAM A. R. M., “Faculty of civil engineering, University Technology, Malaysia”, ”Application of polymer in concrete construction“, 2007, 19.
Hayder A. S., “University of Technology”, “Ceramic Filled Polymer Matrix Composite used for Biomedical Application”, 2010, 59.
Ahmed J. K., Haleem A. H. & Omran A. R., “Effect of Glass fiber surface treatment on the flexural strength and interfacial properties of glass fiber-polyester composite”.
Anand Kumar Gupta, V. R. Balakrishnan and S. K. Tiwary, “International Journal Polymer Technology, Vol. 1, No.2-3, 2009, PP 181-188.