Experimental and CFD Investigation the Effect of Solid Particle Height in Water-Solid Flow in Fluidized Bed Column
International Journal of Mechanical Engineering and Applications
Volume 3, Issue 3, June 2015, Pages: 37-45
Received: May 22, 2015;
Accepted: Jun. 3, 2015;
Published: Jun. 17, 2015
Views 5101 Downloads 224
Riyadh S. Al-Turaihi, Mechanical Department, College of Engineering, Babylon University, Babylon, Iraq
Sarah H. Oleiwi, Mechanical Department, College of Engineering, Babylon University, Babylon, Iraq
The liquid solid fluidized beds have been usually used in catalytic cracking, ion exchange, crystallization, and particle classification. Fluidized bed column has investigated experimentally and numerically. A numerical investigation has been done by using computational fluid dynamic software ANSYS Fluent 15.0. In this study, a spherical stainless steel has used as solid particle fluidized continuously by water. Three different values of water flow rate (10, 15, 20 l/min) have used with three different values of static head of the solid particles (2, 2.5, 3 cm). The pressure of the fluidized bed has been measured at four different location of the test section 20 cm apart and the flow behavior at the test section has monitored by using AOS high speed camera. The experimental data has compared with numerical solution and a good agreement has been found. It can be observed that the expansion of the solid particles and the pressure inside the bed increased as the water flow rate and static bed height increased.
Riyadh S. Al-Turaihi,
Sarah H. Oleiwi,
Experimental and CFD Investigation the Effect of Solid Particle Height in Water-Solid Flow in Fluidized Bed Column, International Journal of Mechanical Engineering and Applications.
Vol. 3, No. 3,
2015, pp. 37-45.
Reza Davarnejad, Reza Eshghipour, Jafar Abdi and Farhad Banisharif Dehkordi, “CFD Modeling of a Binary Liquid-Solid Fluidized Bed”, Middle-East Journal of Scientific Research, 19 (10): 1272-1279, 2014.
Tingwen Li, Aytekin Gel, Sreekanth Pannala, Mehrdad Shahnam, Madhava Syamlal, “CFD simulations of circulating fluidized bed risers, part I: Grid study”, Powder Technology, 254 - 170–180, 2014.
Kenichi Hashizume, Shinichi Morita, Yuki Nakamura, and Akira Wada,” Pressure Drop in Liquid–Solid Circulating Fluidized Beds”, Heat Transfer—Asian Research, 38 (4), 2009.
Dinesh V. Kalaga, Rupesh K. Reddy, Jyeshtharaj B. Joshi, Sameer V. Dalvi, K. Nandkumar, “Liquid phase axial mixing in solid–liquid circulating multistage fluidized bed: CFD modeling and RTD measurements”, Chemical Engineering Journal, 191- 475– 490, 2012.
Riyadh S. Al-Turaihi, Ahmed Kadhim Hussein, Hussain H. Al-Kayiem and H. A. Mohammed, “Experimental Investigation of Various Solid Particle Materials on the Steady State Gas-Solid Fluidized Bed System”, J. Basic. Appl. Sci. Res., 3(7)293-304, 2013.
Youjun Lu, Liang Zhao, Qiang Han, Liping Wei, Ximin Zhang, Liejin Guo, Jinjia Wei, “Minimum fluidization velocities for supercritical water fluidized bed within the range of 633–693 K and 23–27 MPa”, International Journal of Multiphase Flow, 49 - 78–82, 2013.
Chanchal Loha, Himadri Chattopadhyay, Pradip K. Chatterjee, “Euler-Euler CFD modeling of fluidized bed: Influence of specularity coefficient on hydrodynamic behavior”, Particuology, 11- 673– 680, 2013.
Bo LECKNER, Genadij I. PALCHONOK, and Filip JOHNSSON, “PRESSURE FLUCTUATIONS IN GAS FLUIDIZED BEDS”, Original scientific paper, 0354–9836, 6 , 2, 3-11, 2002.
K.V. Ramesh, G.M.J. Raju, G.V.S. Sarma, C. Bhaskara Sarma, “Effect of internal on phase holdups of a three-phase fluidized bed”, Chemical Engineering Journal, 145-393–398, 2009.
Farshid Vejahati, Nader Mahinpey, Naoko Ellis and Mehrdokht B. Nikoo, “CFD Simulation of Gas–Solid Bubbling Fluidized Bed: A New Method for Adjusting Drag Law”, Can. J. Chem. Eng., 87:19–30, 2009.
Ansys 13.0 Help, Fluent Theory Guide, Mixture Multiphase Model.
Ansys Fluent Tutorials, Fluidized bed.