Production of Lightweight Concrete Using Corncob Ash as Replacement of Cement in Concrete
American Journal of Civil Engineering
Volume 7, Issue 1, January 2019, Pages: 17-20
Received: Feb. 11, 2019;
Accepted: Mar. 11, 2019;
Published: Mar. 25, 2019
Views 708 Downloads 287
Sintayehu Assefa, Department of Civil Engineering, Faculty of Civil & Environmental Engineering, Jimma Institute of Technology, Jimma University, Jimma, Ethiopia
Mamaru Dessalegn, Department of Civil Engineering, Faculty of Civil & Environmental Engineering, Jimma Institute of Technology, Jimma University, Jimma, Ethiopia
One of the biggest issues, all over the world is getting affordable house to the community. In developing countries, where it is difficult for most people to satisfy basic needs, construction of modern house is a big challenge. Different ways were tried by researchers and scholars to find alternative construction materials. One of this is replacing the costly construction material of cement with locally available material, especially with those considered as waste. Corncob is an agricultural waste, which is considered as one of binding materials. Very few researchers tried to use corncob ash as a means of producing lightweight concrete. So, this research was aimed to check whether corncob ash is used to produce lightweight concrete by replacing cement as a binding material or not. In order to reach on conclusion, corncob was collected from agricultural farmers and burned in furnace at a temperature of 850°C. The burned ash powder was sieved in order to remove coarser material and replacement of cement was done by 5%, 10%, 15%, 20%, 25%, 30%, and 35% with corncob ash. For each replacement, including control, 3 samples were prepared based on ASTM standards. After curing for 7 and 28 days in curing tank, the weight and compressive strength of samples were checked. Based on the experimental result, as the percentage of corncob ash increase, the weight of cubes decreased and 15% and above corn cob ash replacement makes concrete cubes lightweight. The compressive strength was also decreasing as the amount of replacement increase. However, up to 15% replacement, compressive strength is found within the range of concrete grade requirement.
Production of Lightweight Concrete Using Corncob Ash as Replacement of Cement in Concrete, American Journal of Civil Engineering.
Vol. 7, No. 1,
2019, pp. 17-20.
Copyright © 2019 Authors retain the copyright of this article.
This article is an open access article distributed under the Creative Commons Attribution License (http://creativecommons.org/licenses/by/4.0/
) which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.
J. Pinto et al., “Corn cob lightweight concrete for non-structural applications,” Constr. Build. Mater., vol. 34, pp. 346–351, 2012.
A. Olaniyi and A. A. Umoh, “I NFLUENCE O F C URING M EDIA O N T HE C OMPRESSIVE S TRENGTH O F T ERMITE M OUND -L IME B LENDED C EMENT M ORTAR,” Malaysian J. Civ. Eng., vol. 26, no. 3, pp. 349–365, 2014.
M. Berry, D. Cross, and J. Stephens, “Changing the Environment : An Alternative ‘Green’ Concrete Produced without Portland Cement,” in world of Coal Ash Conference, 2009.
ACI Committee, Building Code Requirements for Structural Concrete (ACI 318-08). American Concrete Institute, 2008.
S. W. Harrison, “A study of alternative building materials and technologies for housing in Bangalore, India,” Constr. Build. Mater., vol. 9, no. 4, pp. 211–217, 1995.
B. Getachew, T. Adugna, and S. Assefa, “INVESTIGATION ON THE EFFECT OF STORAGE TIME DUE TO MOISTURE ABSORPTION OF CEMENT ON THE PROPERTIES OF CONCRETE,” Int. J. Dev. Res., vol. 08, no. 01, pp. 18558–18561, 2018.
C. R. C. X. C. Qiao, B. R. Hg, M. Tyrer, C. S. Poon, “Production of lightweight concrete using incinerator bottom ash,” Constr. Build. Mater., vol. 22, pp. 473–480, 2008.
Y. E. Mark Nisnevich, Gregory Sirotin, Tuvia Schlesinger, “Radiological safety aspects of utilizing coal ashes for production of lightweight concrete,” Fuel, vol. 87, pp. 1610–1616, 2008.
B. J. Tay and W. Yip, “Sludge ash as lightweight concrete material,” J. Environ. Eng., vol. 115, no. 1, pp. 56–64, 1989.
K. D. Oluborode and I. O. Olofintuyi, “Strength Evaluation of Corn cob ash in a blended Portland cement,” Int. J. Innov. Technol., vol. 4, no. 12, pp. 14–17, 2015.
A. M. Neville, Properties of concrete, 5th ed. Trans-Atlantic Publications, Inc., 2011.
Ministry of Urban Development Housing and Construction, Standard Technical Specifications for Building Works. Addis Ababa, 2014.
American Society for Testing and Materials, “Standard Specification for Concrete Aggregates,” in ASTM Standards, vol. 04, West Conshohocken, PA: ASTM International, 2001.
American Society for Testing and Materials, “Standard Practice for Making and Curing Concrete Test Specimens in the,” in ASTM Standards, vol. 04, Farmington, 2000, pp. 1–8.
NRMCA, “Concrete in Practice,” 2003. [Online]. Available: https://www.nrmca.org/aboutconcrete/cips/36p.pdf. [Accessed: 05-Feb-2019].