Optimization of Weight on Bit During Drilling Operation Based on Rate of Penetration

Mehaysen Ahmed Al-Mahasneh

doi:doi:10.11648/j.ogce.20170502.11

| Peer-Reviewed

Optimization of Weight on Bit During Drilling Operation Based on Rate of Penetration

Mehaysen Ahmed Al-Mahasneh

Published in International Journal of Oil, Gas and Coal Engineering (Volume 5, Issue 2)

Received: 31 January 2017 Accepted: 13 February 2017 Published: 15 March 2017

Views: Downloads:

Download PDF

Share This Article

Twitter
Linked In
Facebook

Abstract

Drilling optimization is very important during drilling operation, to save time and reduce cost of operation thus increases the profit. Drilling optimization aims to optimize controllable variables during drilling operation such as weight on bit and bit rotation speed for obtaining maximum drilling rate. In this study had been selected the effects of several parameters during drilling operation. Important parameters such as depth, density, bit weight, rotary speed per minute, efficiently cuttings transported hole is to take into account the factors given in Table 3. It was concluded that average annular fluid velocity is between 414.17 to 581.24ft/min, dominating parameter on cuttings transport, the higher the flow rate. s Another important factor is the mainly the rheological properties of the drilling fluid such as Vis=45-50 s, p.v=12, PH=10, mud weight is between 8.57 ppg to 8.74 ppg. The rate of penetration for the field data had been calculated for several data points. Although the weight on bit has increase from 6600 until 19800 lbs, 1137.41 lbs/in, rate of penetration still in the range of 11.74 ft/hr. The optimized bit weight is 13200 lbs or 1077.55 lbs/in during drilling operation, penetration rate for depth 4330.02 ft is suitable due to formation that is may be high in strength.

Published in	International Journal of Oil, Gas and Coal Engineering (Volume 5, Issue 2)
DOI	10.11648/j.ogce.20170502.11
Page(s)	13-18
Creative Commons	This is an Open Access article, distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution and reproduction in any medium or format, provided the original work is properly cited.
Copyright	Copyright © The Author(s), 2024. Published by Science Publishing Group

Keywords

Drilling Operation, Weight on Bit, Rate of Penetration, Optimization

References

[1]	Tuna, E., 2010. Real-time-optimization of drilling parameters during drilling operations (Thesis). Middle East Technical University.
[2]	Gamier, A. J, and N. H. Van lingen 1959 Phenomena Affecing Drilling Rate at Depth, SPE 1097- G> Annual Fall Meetingof SPE.
[3]	Saleem, Q. T., A. H. Tunio, N. A. Ghirano and S. Irawan, 2011. Is It Possible to Ignore Problems Rising During Vertical Drilling A Review. Res. J. Appl. Sci. Eng. Technol., 3 (11): 1331-1336.
[4]	Vidrine, D. J., E. J. Benit, 1968. Field verification of effect of differential pressure on drilling rate. J. Petroleum Technol., 20 (7). rilling rate. J. Petroleum Technol., 20 (7).
[5]	Tuna, E., 2010. Real-time-optimization of drilling parameters during drilling operations (Thesis). Middle East Technical University.
[6]	Moses, A. A. and F. Egbon, 2011. Semi-analytical models on the effect of drilling fluid properties on Rate of Penetration (ROP), SPE no. 150806. Proceedings of the Nigeria Annual International Conference and Exhibition, 30 July-3, Abuja, Nigeria.
[7]	Irma, G., 2009. Postgraduate Division of the Faculty of Engineering, UNAM and Lorena Berumen, Postgraduate Division of the Faculty of Economy, UNAM, 2009. Optimization model for an oil well drilling program: Mexico case, Oil and Gas Business.
[8]	Bourgoyne A. T. Jr., Millheim K. K., Chenevert M. E., and Young F. S., "Applied Drilling Engineering", Society of Petroleum Engineers Text Book Series, Vol. 1, Richardson, TX, 1986.
[9]	Ozbayoglu M. E., Miska S. Z., Reed T., and Takach N., “Analysis of the Effects of Major Drilling Parameters on Cuttings Transport Efficiency for High-Angle Wells in Coiled Tubing Drilling Operations,” SPE 89334, SPE /IcoTA CT Conf. andExhb., Houston, TX, March 2004.
[10]	Final Drilling Report well RH-39, Drilling Rigs (National E-610, Ideco E-1700), Drilling Department August-2006.
[11]	Final Drilling Report well RH-40 H, Drilling Rigs (National E-610, Ideco E-1700), Drilling Department June-2006.
[12]	Final Drilling Report well RH-42S, Drilling Rigs National E-610, Ideco E-1700), Drilling Department June-2007.

Cite This Article

Plain Text BibTeX RIS

APA Style

Mehaysen Ahmed Al-Mahasneh. (2017). Optimization of Weight on Bit During Drilling Operation Based on Rate of Penetration. International Journal of Oil, Gas and Coal Engineering, 5(2), 13-18. https://doi.org/10.11648/j.ogce.20170502.11

Copy | Download

ACS Style

Mehaysen Ahmed Al-Mahasneh. Optimization of Weight on Bit During Drilling Operation Based on Rate of Penetration. Int. J. Oil Gas Coal Eng. 2017, 5(2), 13-18. doi: 10.11648/j.ogce.20170502.11

Copy | Download

AMA Style

Mehaysen Ahmed Al-Mahasneh. Optimization of Weight on Bit During Drilling Operation Based on Rate of Penetration. Int J Oil Gas Coal Eng. 2017;5(2):13-18. doi: 10.11648/j.ogce.20170502.11

Copy | Download

@article{10.11648/j.ogce.20170502.11,
  author = {Mehaysen Ahmed Al-Mahasneh},
  title = {Optimization of Weight on Bit During Drilling Operation Based on Rate of Penetration},
  journal = {International Journal of Oil, Gas and Coal Engineering},
  volume = {5},
  number = {2},
  pages = {13-18},
  doi = {10.11648/j.ogce.20170502.11},
  url = {https://doi.org/10.11648/j.ogce.20170502.11},
  eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.ogce.20170502.11},
  abstract = {Drilling optimization is very important during drilling operation, to save time and reduce cost of operation thus increases the profit. Drilling optimization aims to optimize controllable variables during drilling operation such as weight on bit and bit rotation speed for obtaining maximum drilling rate. In this study had been selected the effects of several parameters during drilling operation. Important parameters such as depth, density, bit weight, rotary speed per minute, efficiently cuttings transported hole is to take into account the factors given in Table 3. It was concluded that average annular fluid velocity is between 414.17 to 581.24ft/min, dominating parameter on cuttings transport, the higher the flow rate. s Another important factor is the mainly the rheological properties of the drilling fluid such as Vis=45-50 s, p.v=12, PH=10, mud weight is between 8.57 ppg to 8.74 ppg. The rate of penetration for the field data had been calculated for several data points. Although the weight on bit has increase from 6600 until 19800 lbs, 1137.41 lbs/in, rate of penetration still in the range of 11.74 ft/hr. The optimized bit weight is 13200 lbs or 1077.55 lbs/in during drilling operation, penetration rate for depth 4330.02 ft is suitable due to formation that is may be high in strength.},
 year = {2017}
}

Copy | Download

TY  - JOUR
T1  - Optimization of Weight on Bit During Drilling Operation Based on Rate of Penetration
AU  - Mehaysen Ahmed Al-Mahasneh
Y1  - 2017/03/15
PY  - 2017
N1  - https://doi.org/10.11648/j.ogce.20170502.11
DO  - 10.11648/j.ogce.20170502.11
T2  - International Journal of Oil, Gas and Coal Engineering
JF  - International Journal of Oil, Gas and Coal Engineering
JO  - International Journal of Oil, Gas and Coal Engineering
SP  - 13
EP  - 18
PB  - Science Publishing Group
SN  - 2376-7677
UR  - https://doi.org/10.11648/j.ogce.20170502.11
AB  - Drilling optimization is very important during drilling operation, to save time and reduce cost of operation thus increases the profit. Drilling optimization aims to optimize controllable variables during drilling operation such as weight on bit and bit rotation speed for obtaining maximum drilling rate. In this study had been selected the effects of several parameters during drilling operation. Important parameters such as depth, density, bit weight, rotary speed per minute, efficiently cuttings transported hole is to take into account the factors given in Table 3. It was concluded that average annular fluid velocity is between 414.17 to 581.24ft/min, dominating parameter on cuttings transport, the higher the flow rate. s Another important factor is the mainly the rheological properties of the drilling fluid such as Vis=45-50 s, p.v=12, PH=10, mud weight is between 8.57 ppg to 8.74 ppg. The rate of penetration for the field data had been calculated for several data points. Although the weight on bit has increase from 6600 until 19800 lbs, 1137.41 lbs/in, rate of penetration still in the range of 11.74 ft/hr. The optimized bit weight is 13200 lbs or 1077.55 lbs/in during drilling operation, penetration rate for depth 4330.02 ft is suitable due to formation that is may be high in strength.
VL  - 5
IS  - 2
ER  -

Copy | Download

Author Information

Mehaysen Ahmed Al-Mahasneh

Chemical Engineering Department, AL-Huson University College, AL-Balq'a Applied University, Irbid, Jordan

Download PDF

Sections

Plain Text BibTeX RIS

APA Style

Mehaysen Ahmed Al-Mahasneh. (2017). Optimization of Weight on Bit During Drilling Operation Based on Rate of Penetration. International Journal of Oil, Gas and Coal Engineering, 5(2), 13-18. https://doi.org/10.11648/j.ogce.20170502.11

Copy | Download

ACS Style

Mehaysen Ahmed Al-Mahasneh. Optimization of Weight on Bit During Drilling Operation Based on Rate of Penetration. Int. J. Oil Gas Coal Eng. 2017, 5(2), 13-18. doi: 10.11648/j.ogce.20170502.11

Copy | Download

AMA Style

Mehaysen Ahmed Al-Mahasneh. Optimization of Weight on Bit During Drilling Operation Based on Rate of Penetration. Int J Oil Gas Coal Eng. 2017;5(2):13-18. doi: 10.11648/j.ogce.20170502.11

Copy | Download

@article{10.11648/j.ogce.20170502.11,
  author = {Mehaysen Ahmed Al-Mahasneh},
  title = {Optimization of Weight on Bit During Drilling Operation Based on Rate of Penetration},
  journal = {International Journal of Oil, Gas and Coal Engineering},
  volume = {5},
  number = {2},
  pages = {13-18},
  doi = {10.11648/j.ogce.20170502.11},
  url = {https://doi.org/10.11648/j.ogce.20170502.11},
  eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.ogce.20170502.11},
  abstract = {Drilling optimization is very important during drilling operation, to save time and reduce cost of operation thus increases the profit. Drilling optimization aims to optimize controllable variables during drilling operation such as weight on bit and bit rotation speed for obtaining maximum drilling rate. In this study had been selected the effects of several parameters during drilling operation. Important parameters such as depth, density, bit weight, rotary speed per minute, efficiently cuttings transported hole is to take into account the factors given in Table 3. It was concluded that average annular fluid velocity is between 414.17 to 581.24ft/min, dominating parameter on cuttings transport, the higher the flow rate. s Another important factor is the mainly the rheological properties of the drilling fluid such as Vis=45-50 s, p.v=12, PH=10, mud weight is between 8.57 ppg to 8.74 ppg. The rate of penetration for the field data had been calculated for several data points. Although the weight on bit has increase from 6600 until 19800 lbs, 1137.41 lbs/in, rate of penetration still in the range of 11.74 ft/hr. The optimized bit weight is 13200 lbs or 1077.55 lbs/in during drilling operation, penetration rate for depth 4330.02 ft is suitable due to formation that is may be high in strength.},
 year = {2017}
}

Copy | Download

TY  - JOUR
T1  - Optimization of Weight on Bit During Drilling Operation Based on Rate of Penetration
AU  - Mehaysen Ahmed Al-Mahasneh
Y1  - 2017/03/15
PY  - 2017
N1  - https://doi.org/10.11648/j.ogce.20170502.11
DO  - 10.11648/j.ogce.20170502.11
T2  - International Journal of Oil, Gas and Coal Engineering
JF  - International Journal of Oil, Gas and Coal Engineering
JO  - International Journal of Oil, Gas and Coal Engineering
SP  - 13
EP  - 18
PB  - Science Publishing Group
SN  - 2376-7677
UR  - https://doi.org/10.11648/j.ogce.20170502.11
AB  - Drilling optimization is very important during drilling operation, to save time and reduce cost of operation thus increases the profit. Drilling optimization aims to optimize controllable variables during drilling operation such as weight on bit and bit rotation speed for obtaining maximum drilling rate. In this study had been selected the effects of several parameters during drilling operation. Important parameters such as depth, density, bit weight, rotary speed per minute, efficiently cuttings transported hole is to take into account the factors given in Table 3. It was concluded that average annular fluid velocity is between 414.17 to 581.24ft/min, dominating parameter on cuttings transport, the higher the flow rate. s Another important factor is the mainly the rheological properties of the drilling fluid such as Vis=45-50 s, p.v=12, PH=10, mud weight is between 8.57 ppg to 8.74 ppg. The rate of penetration for the field data had been calculated for several data points. Although the weight on bit has increase from 6600 until 19800 lbs, 1137.41 lbs/in, rate of penetration still in the range of 11.74 ft/hr. The optimized bit weight is 13200 lbs or 1077.55 lbs/in during drilling operation, penetration rate for depth 4330.02 ft is suitable due to formation that is may be high in strength.
VL  - 5
IS  - 2
ER  -

Copy | Download