Evolution of Cementite in Hypoeutectoid Steel Wire during Cold Work Hardening in Rolling Process
International Journal of Mineral Processing and Extractive Metallurgy
Volume 3, Issue 3, September 2018, Pages: 60-64
Received: May 28, 2018;
Accepted: Jul. 5, 2018;
Published: Oct. 27, 2018
Views 530 Downloads 46
Wang Bojian, School of Metallurgy Engineering, Xi'an University of Architecture and Technology, Xi'an, China
Ge Xiaochen, Engineering Practice and Training Center, Northwestern Polytechnic University, Xi'an, China
Xiao Qiang, School of Metallurgy Engineering, Xi'an University of Architecture and Technology, Xi'an, China
Liu Shifeng, School of Metallurgy Engineering, Xi'an University of Architecture and Technology, Xi'an, China
Follow on us
Using Φ1.80mm steel wire drawn from Φ6.5mm steel wire was drawn to Φ1.80mm as raw material. Using cold three-rolling process, we got flat wire which size was 0.75mm x 3.17mm by cold three-pass rolling process. Researches shown that 60 steel wire has good plastic deformation ability during cold work processing. The tensile strength and micro-hardness shows linear growth characteristics in the early first stage of cold rolling, then they have exponential growth characteristics in later rollings. That is because in the first rolling process the cementite eventually dissolved in large quantities as the ferrite is turned, deformed, refined and broken. The solution mechanism of cementite is the Gibbs-Thomson effect, i. e. interface energy mechanism.
Rolling, Hypoeutectoidsteel, Cementite, Dissolution
To cite this article
Evolution of Cementite in Hypoeutectoid Steel Wire during Cold Work Hardening in Rolling Process, International Journal of Mineral Processing and Extractive Metallurgy.
Vol. 3, No. 3,
2018, pp. 60-64.
Copyright © 2018 Authors retain the copyright of this article.
This article is an open access article distributed under the Creative Commons Attribution License (http://creativecommons.org/licenses/by/4.0/
) which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.
Xiao Qiang, Wang Bojian, Cao Meng. Research on situation of Forcible-dissolution and Precipitation Phenomenon at Room Temperature Under Severe Plastic Deformation [J]. Hot Working Technology, 2012, 41(20):41-44.
M. V. Belous, V. T. Cherepin, Phys. Met. Metall. 1961, 12, 685-695.
K. Hono, M. Ohnuma, M. Murayama, Cementite decomposition in heavily drawn pearlite steel wire, Scripta Mater., 2001, 977, 44-49.
Min Na. Investigation on Phase Transformation during Severe Plastic Deformation and Aging in Eutectoid Steels [D]. Shanghai：Shanghai Jiao Tong University, 2007.
A. V. Korznikov, Y. V. Ivanisenko, D. V. Laptionok, et al. Influence of severe plastic deformation on structure and phase composition of carbon steel [J]. Nanostructured Materials, 1994, 4(2): 159-167.
J. Languillaume, G. Kapelski, B. Baudelet. Cementite dissolution in heavily cold drawn pearlitic steel wires [J]. ActaMaterialia, 1997, 45(3):1201-1212.
Embury J D, Fisher RM. The structure and properties of drawn pearlite [J]. ActaMetal, 1966, 14:147-153.
Liu Ga, Wang Bojian, Bai He. Study on low temperature spheroidizing annealing process for severe plastic deformation steel wires [J]. Hot Working Technology, 2007, 36(22), 73-76.
Ge XiaoChen, Wang BoJIian, et al. Hardness analysis on oil hardened and tempered flat wire for brush [J] Heat Treatment of Metals, 2015, 40(1), 201-203.
Xiao Qiang, Wang BoJian, Liu ShiIFeng, et al. Microstructure and properties of annealed steel wire prepared by severe plastic deformation [J]. Heat Treatment of Metals, 2013, 38(6):6-9.