| Peer-Reviewed

Bacteriological and Physicochemical Properties of Petroleum-Contaminated Soil Collected from a Mechanic Site in Abuja, North-Central Nigeria

Received: 6 October 2017    Accepted: 7 November 2017    Published: 20 December 2017
Views:       Downloads:
Abstract

Elevated levels of petroleum hydrocarbon and certain heavy metal compounds in soil samples due to environmental and manmade operations can amount to concentrations considered as toxic. Soil samples from 3 different locations, 30 meters from each other were collected and assessed for polycyclic aromatic hydrocarbon (PAH), total petroleum hydrocarbon (TPH), selected heavy metal concentrations, pH, Electrical Conductivity, texture, organic matter, moisture content and bacterial population. The results on the test sites showed that pH range for the workshop soil samples was between 5.08-5.45 in comparison to the control 6.74. Data obtained also revealed that the tested site A alone contained lead (44.91 mg/g) and cadmium (0.01 mg/g). The heavy metal content for sites A, B and C where higher than that of the control site D for which the enrichment factors was determined for sodium (1.07, 3.34, 4.12), copper (2.73, 2.63, 1.57), iron (9.84, 10.67, 9.21), zinc (4.78, 2.58, 2.98), nickel (1.44, 1.11, 1.56) and manganese (2.57, 2.23, 3.77) respectively. The moisture content and electrical conductivity ranged between 44.7-46.5% and 985.6-1124.7 (µS/cm) respectively as opposed to 44.9%, 846.3 (µS/cm) for the control. Total bacterial enumeration revealed a count of 2.28 x 104 (cfu/g), 2.01 x 104 (cfu/g), 1.98 x 103 (cfu/g) and 2.71 x 105 (cfu/g) at sites A, B, C and D respectively. The presence of hydrocarbon and heavy metal pollutants due to the activities at the mechanic workshop resulted in change of known physicochemical properties which in turn affects the ecology as well as life forms in the area.

Published in International Journal of Microbiology and Biotechnology (Volume 3, Issue 1)
DOI 10.11648/j.ijmb.20180301.11
Page(s) 1-6
Creative Commons

This is an Open Access article, distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution and reproduction in any medium or format, provided the original work is properly cited.

Copyright

Copyright © The Author(s), 2024. Published by Science Publishing Group

Keywords

Petroleum Hydrocarbons, Polycyclic Aromatic Hydrocarbons, Heavy Metals, Physicochemical Properties, Mechanic Site, Abuja

References
[1] Bamidele J., and Igiri A., (2011). Growth of seashore paspalum (Paspalum vaginatum L.) in soil contaminated with crude petroleum oil. Journal of Applied Sciences and Environmental Management, 15: 303-306.
[2] Oluyege J. O., Odere J. O., and Kayode J., (2011). Effect of organic manure on the alphatic and aromatic compositions of diesel-oil contaminated soil. Annals of Science, Engineering and Technology, 1: 22-30.
[3] Oyedeji A. A., Adebiyi A., Omotoyinbo M., and Ogunkunle C., (2012). Effect of crude oil-contaminated soil on germination and growth performance of Abelmoschus esculentus L. Moench- a widely cultivated vegetable crop in Nigeria. American Journal of Plant Sciences, 3: 1451-1454.
[4] Sharonova N., and Breus I., (2012). Tolerance of cultivated and wild plants of different taxonomy to soil contamination by kerosene. Science of the Total Environment, 424: 121-129.
[5] Ewetola E. A., (2013). Effect of crude oil pollution on some soil physical properties. Journal of Agriculture and Veterinary Science, 6: 14-17.
[6] Hentati O., Lachhab R., Ayadi M., and Ksibi M., (2013). Toxicity assessment for petroleum-contaminated soil using terrestrial invertebrates and plant bioassays. Environmental Monitoring and Assessment, 185: 2989-2998.
[7] Efe S. I., and Elenwo E. I., (2014). Phytoremediation of crude oil contaminated soil with Axonopus compressus in the Niger Delta region of Nigeria. Natural Resources, 5: 59-67.
[8] Kayode J., Olowoyo O., and Oyedeji A. A., (2009). The effects of used engine oil pollution on the growth and early seedling performance of Vigna uniguiculata and Zea mays L. Research Journal of Soil Biology, 1: 15-19.
[9] Ogunbayo A. O., Bello R. A., and Nwagbara U., (2012). Bioremediation of Engine Oil Contaminated Site. Journal of Emerging Trends in Engineering and Applied Sciences, 3: 483-489.
[10] Boonchan S., Britz M. L., and Stanley G. A., (2000). Degradation and Mineralization of high-molecular weight polycyclic aromatic hydrocarbons by defined fungal-bacterial co-cultures. Applied Environmental Microbiology, 66: 1007-1019.
[11] Moubasher H. A., Hegazy A. K., Mohamed N. H., Moustafa Y. M., Kabiel H. F., Hamad A. A., (2015). Phytoremediation of soils polluted with crude petroleum oil using Bassiascoparia and its associated rhizosphere microorganisms. International Journal of Biodeterioration and Biodegradation, 98: 113-120.
[12] Merrill J. C., Morton J. J. P., and Soileau S. D., (2007). Metals: cadmium. In: Hayes AW (ed) Principles and methods of toxicology, 5th edn. Taylor and Francis, London, pp 665–667.
[13] Useh M. U., Etuk-Udo G. A., and Dauda M. S., (2015). Evaluating the Physico-chemical Properties and Heavy Metals in Soils of Municipal Waste Dumpsites at Kubwa, Abuja, Nigeria. Journal of Chemistry and Chemical Sciences, 5: 654-662.
[14] Hreniuc M., Coman M., and Cioruţa B., (2015). Consideration regarding the soil pollution with oil products in Sacel-Maramures. International Conference of scientific paper AFASES. Brasov: 28-30.
[15] Gennadiev A., Yu N., Pikovskii I., Tsibart A. S., and Smirnova M. A., (2015). Hydrocarbons in Soils: Origin, Composition, and Behavior Review). European Journal of Soil Science, 48:1076-1089.
[16] Gaskin S. E., and Bentham R. H., (2010). Rhizoremediation of hydrocarbon contaminated soil using Australian native grasses. Science of the Total Environment, 408:3683-3688.
[17] Masakorala K., Yao J., Chandankere R., Liu H., Liu W., Cai M., and Choi M. F., (2014). A combined approach of physicochemical and biological Methods for the characterization of petroleum hydrocarbon contaminated soil. Environmental Science and Pollution Research, 21: 454-463.
[18] Schneider T., Keiblinger K. M., Schmid E., Sterflinger-Gleixner K., Ellersdorfer G., Roschitzki B., Richter A., Eberl L., Zechmeister-Boltenstern S., and Riedel K. (2012). Who is who in litter decomposition? Metaproteomics reveals major microbial players and their biogeochemical functions. The ISME Journal, 1: 1-14.
[19] Massenssini A. M., Bonduki V. H. A., Melo C. A. D., Tótola M. R., Ferreira F. A., and Costa, M. D. (2015). Relative importance of soil physico-chemical characteristics and plant species identity to the determination of soil microbial community structure. Applied Soil Ecology, 91: 8–15.
[20] Wang Z., and Stout S. A., (2007). Oil Spill Environmental Forensics: Fingerprinting and Source Identification. Academic Press.
[21] Wang Z., and Stout S. A., (2016). Standard Handbook Oil Spill Environmental Forensics: Fingerprinting and Source Identification. Elsevier/Academic Press.
[22] Lily M. K., Bahuguna A., Dangwal K., and Garg V., (2009). Degradation of benzo [a] pyrene by a novel strain Bacillus subtilis BMT4i (MTCC 9447). Brazilian Journal of Microbiology, 40: 884–892.
[23] Pathak H., Bhatnagar K., and Jaroli D. P., (2011). Physico-chemical Properties of Petroleum Polluted Soil Collected from Transport Nagar (Jaipur). IJFALS, 1: 84-89.
[24] Ibitoye A. A., (2006). Laboratory Manual on Basic Soil Analysis. 2nd Edition, Foladave Nigeria Ltd., Akure, Nigeria, pp. 70.
[25] Bamidele J., and Igiri A., (2011). Growth of seashore paspalum (Paspalum vaginatum L.) in soil contaminated with crude petroleum oil. Journal of Applied Sciences and Environmental Management, 15: 303-306.
[26] Sharma S., and Pathak H., (2017). Physico-chemical properties of petroleum contaminated soil Collected from arid region of Rajasthan (Churu). International Journal of Pharma and Biosciences, 8: 926-932.
[27] Tanee F. B. G., and Kinako P. D. S., (2008). Comparative studies of bio-stimulation and phytoremediation in the mitigation of crude oil toxicity in tropical soil. Journal of Applied Sciences and Environmental Management, 12: 143-147.
[28] Ujowundu C. O., Kalu F. N., Nwaoguikpe R. N., Kalu O. I., Ihejirika C. E., Nwosunjoku E. C., and Okechukwu R. I., (2011). Biochemical and physical characterization of diesel petroleum contaminated soil in southeastern Nigeria. Research Journal of Chemical Science, 1: 57–62.
[29] Khan S. R., Kumar J. I. N., Kumar R. N., and Patel J. G., (2013). Physicochemical properties, heavy metal content and fungal characterization of an old gasoline-contaminated soil site in Anand, Gujarat, India. Environmental and Experimental Biology, 11: 137–143.
[30] Cheraghi M., Sobhanardakani S., Lorestani B., Merrikhpour H., and Parvizi Mosaed H., (2015). Biochemical and Physical Characterization of Petroleum Hydrocarbon Contaminated Soils in Tehran. Journal of Chemical Health Risks, 5: 199–208.
[31] Prashanth L., Kattapagari K. K., Chitturi R. T., Baddam V. R. R., and Prasad L. K., (2015). A review on role of essential trace elements in health and disease. Journal of Dr. NTR University of Health Sciences, 4: 75-85.
[32] Gupta S., Nayek S., Saha R. N., and Satpati S., (2008). Assessment of heavy metal accumulation in macrophyte, agricultural soil and crop plants adjacent to discharge zone of sponge iron factory. Environmental Geology, 55: 731–739.
[33] Khan A., Khan S., Khan M. A., Qamar Z., and Waqas M., (2015). The uptake and bioaccumulation of heavy metals by food plants, their effects on plants nutrients, and associated health risk: a review. Environmental Science and Pollution Research International, 22: 13772-13799.
Cite This Article
  • APA Style

    Kawo Abdullahi Hassan, Yahaya Sani, Olawore Yemisi Ajoke, Ogidi Jonathan Ajisafe. (2017). Bacteriological and Physicochemical Properties of Petroleum-Contaminated Soil Collected from a Mechanic Site in Abuja, North-Central Nigeria. International Journal of Microbiology and Biotechnology, 3(1), 1-6. https://doi.org/10.11648/j.ijmb.20180301.11

    Copy | Download

    ACS Style

    Kawo Abdullahi Hassan; Yahaya Sani; Olawore Yemisi Ajoke; Ogidi Jonathan Ajisafe. Bacteriological and Physicochemical Properties of Petroleum-Contaminated Soil Collected from a Mechanic Site in Abuja, North-Central Nigeria. Int. J. Microbiol. Biotechnol. 2017, 3(1), 1-6. doi: 10.11648/j.ijmb.20180301.11

    Copy | Download

    AMA Style

    Kawo Abdullahi Hassan, Yahaya Sani, Olawore Yemisi Ajoke, Ogidi Jonathan Ajisafe. Bacteriological and Physicochemical Properties of Petroleum-Contaminated Soil Collected from a Mechanic Site in Abuja, North-Central Nigeria. Int J Microbiol Biotechnol. 2017;3(1):1-6. doi: 10.11648/j.ijmb.20180301.11

    Copy | Download

  • @article{10.11648/j.ijmb.20180301.11,
      author = {Kawo Abdullahi Hassan and Yahaya Sani and Olawore Yemisi Ajoke and Ogidi Jonathan Ajisafe},
      title = {Bacteriological and Physicochemical Properties of Petroleum-Contaminated Soil Collected from a Mechanic Site in Abuja, North-Central Nigeria},
      journal = {International Journal of Microbiology and Biotechnology},
      volume = {3},
      number = {1},
      pages = {1-6},
      doi = {10.11648/j.ijmb.20180301.11},
      url = {https://doi.org/10.11648/j.ijmb.20180301.11},
      eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.ijmb.20180301.11},
      abstract = {Elevated levels of petroleum hydrocarbon and certain heavy metal compounds in soil samples due to environmental and manmade operations can amount to concentrations considered as toxic. Soil samples from 3 different locations, 30 meters from each other were collected and assessed for polycyclic aromatic hydrocarbon (PAH), total petroleum hydrocarbon (TPH), selected heavy metal concentrations, pH, Electrical Conductivity, texture, organic matter, moisture content and bacterial population. The results on the test sites showed that pH range for the workshop soil samples was between 5.08-5.45 in comparison to the control 6.74. Data obtained also revealed that the tested site A alone contained lead (44.91 mg/g) and cadmium (0.01 mg/g). The heavy metal content for sites A, B and C where higher than that of the control site D for which the enrichment factors was determined for sodium (1.07, 3.34, 4.12), copper (2.73, 2.63, 1.57), iron (9.84, 10.67, 9.21), zinc (4.78, 2.58, 2.98), nickel (1.44, 1.11, 1.56) and manganese (2.57, 2.23, 3.77) respectively. The moisture content and electrical conductivity ranged between 44.7-46.5% and 985.6-1124.7 (µS/cm) respectively as opposed to 44.9%, 846.3 (µS/cm) for the control. Total bacterial enumeration revealed a count of 2.28 x 104 (cfu/g), 2.01 x 104 (cfu/g), 1.98 x 103 (cfu/g) and 2.71 x 105 (cfu/g) at sites A, B, C and D respectively. The presence of hydrocarbon and heavy metal pollutants due to the activities at the mechanic workshop resulted in change of known physicochemical properties which in turn affects the ecology as well as life forms in the area.},
     year = {2017}
    }
    

    Copy | Download

  • TY  - JOUR
    T1  - Bacteriological and Physicochemical Properties of Petroleum-Contaminated Soil Collected from a Mechanic Site in Abuja, North-Central Nigeria
    AU  - Kawo Abdullahi Hassan
    AU  - Yahaya Sani
    AU  - Olawore Yemisi Ajoke
    AU  - Ogidi Jonathan Ajisafe
    Y1  - 2017/12/20
    PY  - 2017
    N1  - https://doi.org/10.11648/j.ijmb.20180301.11
    DO  - 10.11648/j.ijmb.20180301.11
    T2  - International Journal of Microbiology and Biotechnology
    JF  - International Journal of Microbiology and Biotechnology
    JO  - International Journal of Microbiology and Biotechnology
    SP  - 1
    EP  - 6
    PB  - Science Publishing Group
    SN  - 2578-9686
    UR  - https://doi.org/10.11648/j.ijmb.20180301.11
    AB  - Elevated levels of petroleum hydrocarbon and certain heavy metal compounds in soil samples due to environmental and manmade operations can amount to concentrations considered as toxic. Soil samples from 3 different locations, 30 meters from each other were collected and assessed for polycyclic aromatic hydrocarbon (PAH), total petroleum hydrocarbon (TPH), selected heavy metal concentrations, pH, Electrical Conductivity, texture, organic matter, moisture content and bacterial population. The results on the test sites showed that pH range for the workshop soil samples was between 5.08-5.45 in comparison to the control 6.74. Data obtained also revealed that the tested site A alone contained lead (44.91 mg/g) and cadmium (0.01 mg/g). The heavy metal content for sites A, B and C where higher than that of the control site D for which the enrichment factors was determined for sodium (1.07, 3.34, 4.12), copper (2.73, 2.63, 1.57), iron (9.84, 10.67, 9.21), zinc (4.78, 2.58, 2.98), nickel (1.44, 1.11, 1.56) and manganese (2.57, 2.23, 3.77) respectively. The moisture content and electrical conductivity ranged between 44.7-46.5% and 985.6-1124.7 (µS/cm) respectively as opposed to 44.9%, 846.3 (µS/cm) for the control. Total bacterial enumeration revealed a count of 2.28 x 104 (cfu/g), 2.01 x 104 (cfu/g), 1.98 x 103 (cfu/g) and 2.71 x 105 (cfu/g) at sites A, B, C and D respectively. The presence of hydrocarbon and heavy metal pollutants due to the activities at the mechanic workshop resulted in change of known physicochemical properties which in turn affects the ecology as well as life forms in the area.
    VL  - 3
    IS  - 1
    ER  - 

    Copy | Download

Author Information
  • Department of Microbiology, Faculty of Life Sciences, Bayero University, Kano, Nigeria

  • Department of Microbiology, Faculty of Life Sciences, Bayero University, Kano, Nigeria

  • Department of Microbiology, Faculty of Life Sciences, Bayero University, Kano, Nigeria

  • Department of Applied Mathematics, National Mathematical Centre, Sheda-Abuja, Nigeria

  • Sections