American Journal of Physics and Applications
Volume 6, Issue 3, May 2018, Pages: 63-75
Received: Feb. 22, 2018;
Accepted: Mar. 19, 2018;
Published: May 10, 2018
Views 1870 Downloads 220
Herianto, Petroleum Engineering Department, Faculty of Technology and Mineral, UPN “Veteran” Yogyakarta, D. I. Yogyakarta, Indonesia
The rate of penetration has an important role in the success of a drilling operation, this is because if the rate of penetration is not optimum will have an impact on the cost incurred. Some factors that influence the rate of penetration are the weight on bit, rotation per minute and horsepower. Based on the analysis obtained WOB and RPM values are optimum so that optimization is done on horsepower. In this case study the well that will be analyzed is vertical well so that bit’s hydraulic optimization is performed using Bit Hydraulic Horse Power (BHHP) method by adjusting the nozzle size and circulation rate, this method will be optimum if BHHP / HPs ratio is 65%. Evaluation on trajectory 12 ¼ well “SGT-01” field “Tranusa", obtained bit’s hydraulics on the actual conditions at 2657.48 ft - 2723.10 ft depth interval obtained Bit Hydraulic Horse Power (BHHP) of 232.67 hp, Horse Power Surface (HPs) 499.82 hp, Horse Power per Square Inches (HSI) of 1.67 hp / in² and percentage (BHHP / HPs) of 46.55% (<65%) indicating less optimum then optimized hydraulic bit circulation rate optimized to 710 gpm with Horsepower Hydraulic Horse Power (HPH) of 936.47 hp, Horse Power per Square Inches (HSI) of 5.4 hp / in² and percentage (BHHP / HPs) of 65% (already optimum). The final result of the evaluation and optimization of bit hydraulics and the removal of cutting is predicted to increase ROP from 46 fph to 125.66 fph.
Optimization of Hydraulic Horsepower to Predict the Rate of Penetration, American Journal of Physics and Applications.
Vol. 6, No. 3,
2018, pp. 63-75.
Copyright © 2018 Authors retain the copyright of this article.
This article is an open access article distributed under the Creative Commons Attribution License (http://creativecommons.org/licenses/by/4.0/
) which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.
Saleem. Q. T,. A. H. Tunio, N. A. Ghirano and S. Irawan, 2011. Is It Possible to Ignore Problems Rising During Vertical Drilling A. Review. Res. J. Appl. Sci. Eng. Technol., 3 (11): 1331-1336.
T. Eren and M. E. Ozbayoglu. Real time optimization of drilling parameters during drilling operations. In SPE Oil and Gas India Conference and Exhibition, 2010, SPE-129126, 2010.
F. E. Beck, Arco Alaska, Inc., and J. W. Powelland MarioZamora, The Effect of Rheology on Rate of Penetration SPE/lADC Drilling Conference held In Amsterdam, 28 February-2 March 1995.
A. M. Palaman, M. K. Ghassem Al-Askari, B. Salmani, B. D. Al-Anazi and M. Masihi, “Effect of Drilling Fluid Properties on Rate of Penetration”, Scientic Original Paper, 2009.
Moses, A. A. and F. Engbon, 2011. Semi-analyical models on the effect of drilling fluid properties on Rate of Penetration (ROP), SPE no. 150806. Proceedings of the Nigeria Annual International Conference and Exhibition, 30 July-3, Abuja, Nigeria.
Bourgoyne, A. T., et al. (1986), “Applied Drilling Engineering”, Society of Drilling Engineerings, Richardson, Texas.
Gatlin, C. (1960), “Petroleum Engineering Drilling and Well Completion”, Prentice Hall Inc., Englewood Clift, New Jersey.
Lummus. J. L. (1986), Drilling Fluids Optimization”, Penn Well Publishing Co., Tulsa Oklahoma.
Millpark Staff (1993), “Drilling Fluid Manual”, Millaprk Drilling Fluids, A Baker Hughes Company.
Preston L. Moore (1974)., “Drilling Practices Manual”, The Petroleum Publishing Co., Tulsa.
Rabia, H. (1985), “Oil Well Drilling Engineering Principles and Practice”, University of New Castle, UK.
Rudi Rubiandini R. S “Diklat Kuliah Teknik dan Alat Pemboran”.
T. I. Larsen, A. A. Pilehvari, and J. J. Azar (1997), SPE Paper “Development of a New Cutting Transport Model for High-Angle Wellbores Including Horizontal Well”, SPE No 25872.
Ziedler. H. Udo, Dr. P. E. (1988), “Drilling Fluid Technology applied to Horisontal Drilling”, Maurer Engineering Inc, Houston, Texas.
Herianto. Dkk (2001) Optimisasi Hidrolika Pada Penggunaan Down Hole Mud Motor (DHMM) dengan Konsep Minimum Annular Velocity untuk Pemboran Sumur-Sumur Berarah.
Norton J Lapeyrouse, “Formulas and Calculations for Drilling, Production and Workover, Second Edition”.