Design and Implementation of a Low-Cost Multi-Waveform Generator Using Arduino Mega and AD9833 with LCD-Based Interactive Control

Shrugal Agarwal; Priyam Parikh

doi:doi:10.11648/j.cssp.20251202.12

Research Article |

| Peer-Reviewed

Design and Implementation of a Low-Cost Multi-Waveform Generator Using Arduino Mega and AD9833 with LCD-Based Interactive Control

Shrugal Agarwal, Priyam Parikh^*

Published in Science Journal of Circuits, Systems and Signal Processing (Volume 12, Issue 2)

Received: 15 October 2025 Accepted: 27 October 2025 Published: 24 December 2025

Views: Downloads:

Download PDF

Share This Article

Twitter
Linked In
Facebook

Abstract

Signal generators are essential instruments for testing, measurement, and embedded system validation. Commercial function generators, however, are often expensive and non-customizable for educational or prototyping environments. This study presents the design and realization of a low-cost, microcontroller-based multi-waveform generator capable of producing sine, triangular, sawtooth, and square waveforms with adjustable frequency, phase, and duty cycle. The system integrates an Arduino Mega 2560 controller with an AD9833 Direct Digital Synthesis (DDS) module for high-precision sine and triangular outputs, while hardware-timed PWM channels generate sawtooth and square waveforms. Three potentiometers provide real-time user control of frequency (50 Hz-1 kHz), phase (0°-360°), and duty ratio (0-100%), and a 16×2 I²C LCD displays the selected waveform parameters. Experimental characterization demonstrates frequency accuracy of ±0.05% and phase error within ±2° for AD9833-based signals, and total harmonic distortion (THD) below 0.8% for sine output up to 1 kHz. PWM-derived waveforms exhibit amplitude linearity of 96-98% and negligible drift across 8 h continuous operation. Compared with conventional analog Wien-bridge or XR2206-based function generators, the proposed system offers higher frequency stability, lower power consumption (≈310 mW), and greater flexibility for digital control at less than 15 USD total cost. The developed prototype successfully reproduces clean, noise-free waveforms observable on an oscilloscope and matches reference laboratory generators with an RMS amplitude deviation under 0.03 V (5 V scale). The compact and modular design enables rapid educational deployment and portable instrumentation. Future enhancements may include amplitude modulation through DAC expansion, frequency sweep automation, and PC-linked waveform visualization. The proposed design thus bridges the gap between low-cost educational tools and professional waveform generation, demonstrating the potential of open-source microcontroller architectures for accurate, user-interactive signal synthesis.

Published in	Science Journal of Circuits, Systems and Signal Processing (Volume 12, Issue 2)
DOI	10.11648/j.cssp.20251202.12
Page(s)	30-46
Creative Commons	This is an Open Access article, distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution and reproduction in any medium or format, provided the original work is properly cited.
Copyright	Copyright © The Author(s), 2025. Published by Science Publishing Group

Keywords

AD9833 Direct Digital Synthesizer (DDS), Function Generator, Signal Generation, PWM Waveform Synthesis, Sawtooth and Square Wave Generation

References

[1]	Analog Devices, AD9833: Low Power, Programmable Waveform Generator, Data Sheet, 2023. [Online]. Available: https://www.analog.com/media/en/technical-documentation/data-sheets/ad9833.pdf
[2]	“AD9833 Function Generator Using Arduino,” Hackster. io, 2023. [Online]. Available: https://www.hackster.io/john-bradnam/ad9833-function-generator-180317
[3]	D. Das, “Build Your Own Function Generator with Arduino and AD9833 DDS Module,” CircuitDigest, 2021. [Online]. Available: https://circuitdigest.com/microcontroller-projects/arduino-ad9833-function-generator
[4]	V. Smolaninovs and M. Terauds, “Microcontroller-Based Electronic Laboratory Measurement Device for Distance Education,” Electronics, vol. 14, no. 3, p. 438, 2025. https://doi.org/10.3390/electronics14030438
[5]	N. Zoric, A. Zoric, S. Ilic, and B. Jovanovic, “A simple low-cost function generator controlled by Android application,” in Proc. Int. Scientific Conf. UNITECH 2022, Gabrovo, Bulgaria, Nov. 18-19, 2022, pp. 95-99.
[6]	J. Qi, W. Liu, and Y. Zhang, “Design and Analysis of a Low-Cost Wave Generator Based on Direct Digital Synthesis,” J. Electr. Comput. Eng., vol. 2016, Article ID 8519048, 2016. https://doi.org/10.1155/2016/8519048
[7]	A. Ben-Atitallah et al., “An Effective Obstacle Detection System Using Deep Learning Advantages to Aid Blind and Visually Impaired Navigation,” Ain Shams Eng. J., vol. 15, no. 2, 2024, Art. 102387. https://doi.org/10.1016/j.asej.2023.102387
[8]	D. Das and R. Saha, “Arduino-Based DDS Function Generator Using AD9833,” Circuit Digest, 2021. [Online]. Available: https://circuitdigest.com/microcontroller-projects/arduino-ad9833-function-generator
[9]	T. S. Wei, N. Sulaiman, N. Kamsani and N. A. M. Yunus, "Dual control Direct Digital Synthesizer (DCDDS) for electronic testing and experimental work," 2014 4th International Conference on Engineering Technology and Technopreneuship (ICE2T), Kuala Lumpur, Malaysia, 2014, pp. 137-142, https://doi.org/10.1109/ICE2T.2014.7006234
[10]	H. H. Shaker, H. Kasban, A. A. Saleh, and M. Dessouky, “Development of a low-cost digital gamma spectrometer using an STM32F4 microcontroller,” J. Anal. At. Spectrom., vol. 39, no. 6, pp. 1523-1528, 2024. https://doi.org/10.1039/D4JA00050A
[11]	Sharma, A., Sun, Y., & Simpson, O. (2021). Design and implementation of a re-configurable versatile direct digital synthesis-based pulse generator. IEEE Transactions on Instrumentation and Measurement, 70, 1-14.
[12]	Mohiuddin, M., Kadir, K., Roslan, N. F., Maricar, N., Khan, S., Islam, M., & Aboadla, E. (2024, July). Synchronous Machine Torque Ripple Reduction using Seesaw Space Vector Pulse Width Modulation (SSSVPWM). In 2024 IEEE 10th International Conference on Smart Instrumentation, Measurement and Applications (ICSIMA) (pp. 36-41). IEEE.
[13]	Wu, X., Wang, X. H., Zhen, Q. H., Xue, G. Q., He, C., Lv, Y. J., ... & Guo, Q. H. (2025). Designing and Testing of a High-Power Transient Electromagnetic Transmitter with Arbitrary Coded Waveforms. Applied Geophysics, 1-14.
[14]	Abdelbaki, M., Esmail, R., Eltabakh, H., Salman, O., Habiba, M., Mourad, J., & Sherif, S. (2025, July). Non-Invasive Tissue Damage Detection Using Micro Interdigitated Electrodes and Arduino-Based Impedance Spectroscopy. In 2025 International Telecommunications Conference (ITC-Egypt) (pp. 447-452). IEEE.
[15]	Nasibov, A. S., Bagramov, V. G., Berezhnoy, K. V., Plokhinsky, Y. V., Tasmagulov, I. D., Danielyan, G. L., ... & Chevokin, V. K. (2021, December). Multichannel system for recording sub-nanosecond pulses of gas and semiconductor radiation sources. In XV International Conference on Pulsed Lasers and Laser Applications (Vol. 12086, pp. 357-364). SPIE.
[16]	Atci, A., Unal, E., & Akgol, O. (2024). A Low-Cost Data Acquisition System Design for Multifunctional Test Equipment in Electronics Laboratories. Electronics, 13(24), 4937.
[17]	Daodong, Z., Yikai, P., & Hongping, P. (2021, August). Design of DDS Signal Generator Based on FPGA. In 2021 4th International Conference on Pattern Recognition and Artificial Intelligence (PRAI) (pp. 51-54). IEEE.
[18]	Chekka, A. B., & Aggala, N. J. (2021, June). High frequency Chirp signal generator using multi DDS approach on FPGA. In 2021 5th International Conference on Trends in Electronics and Informatics (ICOEI) (pp. 137-142). IEEE.
[19]	Ye, S., Long, Z., Zhao, H., Ju, J., Yao, M., Li, X., & Zhang, X. (2023). Investigation to dual-frequency direct digital synthesis and resonance frequency tracking in power ultrasonic generator. IEEE Transactions on Circuits and Systems I: Regular Papers, 70(11), 4435-4446.
[20]	Kweon, S. J., Rafi, A. K., Cheon, S. I., Je, M., & Ha, S. (2022). On-chip sinusoidal signal generators for electrical impedance spectroscopy: Methodological review. IEEE Transactions on Biomedical Circuits and Systems, 16(3), 337-360.
[21]	Ruo Roch, M., & Martina, M. (2022). VirtLAB: A Low-Cost Platform for Electronics Lab Experiments. Sensors, 22(13), 4840. https://doi.org/10.3390/s22134840
[22]	Dong, J., & Yue, S. (2025, July). Design and Performance Optimisation Analysis of Fpga Dds Signal Generator With Dynamic Frequency Control. In 2025 44th Chinese Control Conference (CCC) (pp. 3769-3774). IEEE.
[23]	ICL, XR2206 Monolithic Function Generator: Sine, Triangle, and Square Wave Outputs, XR2206 Datasheet, 2023. [Online]. Available: https://www.intersil.com/content/dam/Intersil/documents/xr22/xr2206.pdf
[24]	Maxim Integrated, ICL8038 Precision Waveform Generator/Voltage-Controlled Oscillator, ICL8038 Datasheet, 2023. [Online]. Available: https://datasheets.maximintegrated.com/en/ds/ICL8038.pdf

Cite This Article

Plain Text BibTeX RIS

APA Style

Agarwal, S., Parikh, P. (2025). Design and Implementation of a Low-Cost Multi-Waveform Generator Using Arduino Mega and AD9833 with LCD-Based Interactive Control. Science Journal of Circuits, Systems and Signal Processing, 12(2), 30-46. https://doi.org/10.11648/j.cssp.20251202.12

Copy | Download

ACS Style

Agarwal, S.; Parikh, P. Design and Implementation of a Low-Cost Multi-Waveform Generator Using Arduino Mega and AD9833 with LCD-Based Interactive Control. Sci. J. Circuits Syst. Signal Process. 2025, 12(2), 30-46. doi: 10.11648/j.cssp.20251202.12

Copy | Download

AMA Style

Agarwal S, Parikh P. Design and Implementation of a Low-Cost Multi-Waveform Generator Using Arduino Mega and AD9833 with LCD-Based Interactive Control. Sci J Circuits Syst Signal Process. 2025;12(2):30-46. doi: 10.11648/j.cssp.20251202.12

Copy | Download

@article{10.11648/j.cssp.20251202.12,
  author = {Shrugal Agarwal and Priyam Parikh},
  title = {Design and Implementation of a Low-Cost Multi-Waveform Generator Using Arduino Mega and AD9833 with LCD-Based Interactive Control},
  journal = {Science Journal of Circuits, Systems and Signal Processing},
  volume = {12},
  number = {2},
  pages = {30-46},
  doi = {10.11648/j.cssp.20251202.12},
  url = {https://doi.org/10.11648/j.cssp.20251202.12},
  eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.cssp.20251202.12},
  abstract = {Signal generators are essential instruments for testing, measurement, and embedded system validation. Commercial function generators, however, are often expensive and non-customizable for educational or prototyping environments. This study presents the design and realization of a low-cost, microcontroller-based multi-waveform generator capable of producing sine, triangular, sawtooth, and square waveforms with adjustable frequency, phase, and duty cycle. The system integrates an Arduino Mega 2560 controller with an AD9833 Direct Digital Synthesis (DDS) module for high-precision sine and triangular outputs, while hardware-timed PWM channels generate sawtooth and square waveforms. Three potentiometers provide real-time user control of frequency (50 Hz-1 kHz), phase (0°-360°), and duty ratio (0-100%), and a 16×2 I²C LCD displays the selected waveform parameters. Experimental characterization demonstrates frequency accuracy of ±0.05% and phase error within ±2° for AD9833-based signals, and total harmonic distortion (THD) below 0.8% for sine output up to 1 kHz. PWM-derived waveforms exhibit amplitude linearity of 96-98% and negligible drift across 8 h continuous operation. Compared with conventional analog Wien-bridge or XR2206-based function generators, the proposed system offers higher frequency stability, lower power consumption (≈310 mW), and greater flexibility for digital control at less than 15 USD total cost. The developed prototype successfully reproduces clean, noise-free waveforms observable on an oscilloscope and matches reference laboratory generators with an RMS amplitude deviation under 0.03 V (5 V scale). The compact and modular design enables rapid educational deployment and portable instrumentation. Future enhancements may include amplitude modulation through DAC expansion, frequency sweep automation, and PC-linked waveform visualization. The proposed design thus bridges the gap between low-cost educational tools and professional waveform generation, demonstrating the potential of open-source microcontroller architectures for accurate, user-interactive signal synthesis.},
 year = {2025}
}

Copy | Download

TY  - JOUR
T1  - Design and Implementation of a Low-Cost Multi-Waveform Generator Using Arduino Mega and AD9833 with LCD-Based Interactive Control
AU  - Shrugal Agarwal
AU  - Priyam Parikh
Y1  - 2025/12/24
PY  - 2025
N1  - https://doi.org/10.11648/j.cssp.20251202.12
DO  - 10.11648/j.cssp.20251202.12
T2  - Science Journal of Circuits, Systems and Signal Processing
JF  - Science Journal of Circuits, Systems and Signal Processing
JO  - Science Journal of Circuits, Systems and Signal Processing
SP  - 30
EP  - 46
PB  - Science Publishing Group
SN  - 2326-9073
UR  - https://doi.org/10.11648/j.cssp.20251202.12
AB  - Signal generators are essential instruments for testing, measurement, and embedded system validation. Commercial function generators, however, are often expensive and non-customizable for educational or prototyping environments. This study presents the design and realization of a low-cost, microcontroller-based multi-waveform generator capable of producing sine, triangular, sawtooth, and square waveforms with adjustable frequency, phase, and duty cycle. The system integrates an Arduino Mega 2560 controller with an AD9833 Direct Digital Synthesis (DDS) module for high-precision sine and triangular outputs, while hardware-timed PWM channels generate sawtooth and square waveforms. Three potentiometers provide real-time user control of frequency (50 Hz-1 kHz), phase (0°-360°), and duty ratio (0-100%), and a 16×2 I²C LCD displays the selected waveform parameters. Experimental characterization demonstrates frequency accuracy of ±0.05% and phase error within ±2° for AD9833-based signals, and total harmonic distortion (THD) below 0.8% for sine output up to 1 kHz. PWM-derived waveforms exhibit amplitude linearity of 96-98% and negligible drift across 8 h continuous operation. Compared with conventional analog Wien-bridge or XR2206-based function generators, the proposed system offers higher frequency stability, lower power consumption (≈310 mW), and greater flexibility for digital control at less than 15 USD total cost. The developed prototype successfully reproduces clean, noise-free waveforms observable on an oscilloscope and matches reference laboratory generators with an RMS amplitude deviation under 0.03 V (5 V scale). The compact and modular design enables rapid educational deployment and portable instrumentation. Future enhancements may include amplitude modulation through DAC expansion, frequency sweep automation, and PC-linked waveform visualization. The proposed design thus bridges the gap between low-cost educational tools and professional waveform generation, demonstrating the potential of open-source microcontroller architectures for accurate, user-interactive signal synthesis.
VL  - 12
IS  - 2
ER  -

Copy | Download

Author Information

Shrugal Agarwal

Higher Secondary Department, Delhi Public School, Ahmedabad, India

Contact Email
Priyam Parikh

Product Design Department, Anant National University, Ahmedabad, India

Contact Email

http://orcid.org/0000-0001-8538-3669

Download PDF

Submit an Article

Sections

Plain Text BibTeX RIS

APA Style

Agarwal, S., Parikh, P. (2025). Design and Implementation of a Low-Cost Multi-Waveform Generator Using Arduino Mega and AD9833 with LCD-Based Interactive Control. Science Journal of Circuits, Systems and Signal Processing, 12(2), 30-46. https://doi.org/10.11648/j.cssp.20251202.12

Copy | Download

ACS Style

Agarwal, S.; Parikh, P. Design and Implementation of a Low-Cost Multi-Waveform Generator Using Arduino Mega and AD9833 with LCD-Based Interactive Control. Sci. J. Circuits Syst. Signal Process. 2025, 12(2), 30-46. doi: 10.11648/j.cssp.20251202.12

Copy | Download

AMA Style

Agarwal S, Parikh P. Design and Implementation of a Low-Cost Multi-Waveform Generator Using Arduino Mega and AD9833 with LCD-Based Interactive Control. Sci J Circuits Syst Signal Process. 2025;12(2):30-46. doi: 10.11648/j.cssp.20251202.12

Copy | Download

@article{10.11648/j.cssp.20251202.12,
  author = {Shrugal Agarwal and Priyam Parikh},
  title = {Design and Implementation of a Low-Cost Multi-Waveform Generator Using Arduino Mega and AD9833 with LCD-Based Interactive Control},
  journal = {Science Journal of Circuits, Systems and Signal Processing},
  volume = {12},
  number = {2},
  pages = {30-46},
  doi = {10.11648/j.cssp.20251202.12},
  url = {https://doi.org/10.11648/j.cssp.20251202.12},
  eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.cssp.20251202.12},
  abstract = {Signal generators are essential instruments for testing, measurement, and embedded system validation. Commercial function generators, however, are often expensive and non-customizable for educational or prototyping environments. This study presents the design and realization of a low-cost, microcontroller-based multi-waveform generator capable of producing sine, triangular, sawtooth, and square waveforms with adjustable frequency, phase, and duty cycle. The system integrates an Arduino Mega 2560 controller with an AD9833 Direct Digital Synthesis (DDS) module for high-precision sine and triangular outputs, while hardware-timed PWM channels generate sawtooth and square waveforms. Three potentiometers provide real-time user control of frequency (50 Hz-1 kHz), phase (0°-360°), and duty ratio (0-100%), and a 16×2 I²C LCD displays the selected waveform parameters. Experimental characterization demonstrates frequency accuracy of ±0.05% and phase error within ±2° for AD9833-based signals, and total harmonic distortion (THD) below 0.8% for sine output up to 1 kHz. PWM-derived waveforms exhibit amplitude linearity of 96-98% and negligible drift across 8 h continuous operation. Compared with conventional analog Wien-bridge or XR2206-based function generators, the proposed system offers higher frequency stability, lower power consumption (≈310 mW), and greater flexibility for digital control at less than 15 USD total cost. The developed prototype successfully reproduces clean, noise-free waveforms observable on an oscilloscope and matches reference laboratory generators with an RMS amplitude deviation under 0.03 V (5 V scale). The compact and modular design enables rapid educational deployment and portable instrumentation. Future enhancements may include amplitude modulation through DAC expansion, frequency sweep automation, and PC-linked waveform visualization. The proposed design thus bridges the gap between low-cost educational tools and professional waveform generation, demonstrating the potential of open-source microcontroller architectures for accurate, user-interactive signal synthesis.},
 year = {2025}
}

Copy | Download

TY  - JOUR
T1  - Design and Implementation of a Low-Cost Multi-Waveform Generator Using Arduino Mega and AD9833 with LCD-Based Interactive Control
AU  - Shrugal Agarwal
AU  - Priyam Parikh
Y1  - 2025/12/24
PY  - 2025
N1  - https://doi.org/10.11648/j.cssp.20251202.12
DO  - 10.11648/j.cssp.20251202.12
T2  - Science Journal of Circuits, Systems and Signal Processing
JF  - Science Journal of Circuits, Systems and Signal Processing
JO  - Science Journal of Circuits, Systems and Signal Processing
SP  - 30
EP  - 46
PB  - Science Publishing Group
SN  - 2326-9073
UR  - https://doi.org/10.11648/j.cssp.20251202.12
AB  - Signal generators are essential instruments for testing, measurement, and embedded system validation. Commercial function generators, however, are often expensive and non-customizable for educational or prototyping environments. This study presents the design and realization of a low-cost, microcontroller-based multi-waveform generator capable of producing sine, triangular, sawtooth, and square waveforms with adjustable frequency, phase, and duty cycle. The system integrates an Arduino Mega 2560 controller with an AD9833 Direct Digital Synthesis (DDS) module for high-precision sine and triangular outputs, while hardware-timed PWM channels generate sawtooth and square waveforms. Three potentiometers provide real-time user control of frequency (50 Hz-1 kHz), phase (0°-360°), and duty ratio (0-100%), and a 16×2 I²C LCD displays the selected waveform parameters. Experimental characterization demonstrates frequency accuracy of ±0.05% and phase error within ±2° for AD9833-based signals, and total harmonic distortion (THD) below 0.8% for sine output up to 1 kHz. PWM-derived waveforms exhibit amplitude linearity of 96-98% and negligible drift across 8 h continuous operation. Compared with conventional analog Wien-bridge or XR2206-based function generators, the proposed system offers higher frequency stability, lower power consumption (≈310 mW), and greater flexibility for digital control at less than 15 USD total cost. The developed prototype successfully reproduces clean, noise-free waveforms observable on an oscilloscope and matches reference laboratory generators with an RMS amplitude deviation under 0.03 V (5 V scale). The compact and modular design enables rapid educational deployment and portable instrumentation. Future enhancements may include amplitude modulation through DAC expansion, frequency sweep automation, and PC-linked waveform visualization. The proposed design thus bridges the gap between low-cost educational tools and professional waveform generation, demonstrating the potential of open-source microcontroller architectures for accurate, user-interactive signal synthesis.
VL  - 12
IS  - 2
ER  -

Copy | Download